|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
January 14, 2013, 11:56 AM | #1 |
Junior Member
Join Date: January 9, 2013
Posts: 14
|
Best Starter Relaoding set up
Looking to start reloading but need help in finding the right set up for a beginner like me. I have looked at several kits from single, turret and all in one but not sure what is best for a beginner. Any advise would be helpful.
|
January 14, 2013, 12:47 PM | #2 |
Senior Member
Join Date: June 25, 2009
Location: Stuttgart, AR
Posts: 1,569
|
A single stage press or turret is a good starter. Give us a little more information such as:
What will you be loading? Rifle, pistol or shotgun? Caliber? Volume you think you will be loading/shooting per week or month or year? A good book for the basics is The ABCs of Reloading.
__________________
A lack of planning on your part does not necessarily constitute an emergency on my part. |
January 14, 2013, 12:55 PM | #3 |
Senior Member
Join Date: March 31, 2010
Location: Communist State of IL.
Posts: 1,562
|
Lee's Classic Turret with the Pro Disk powder measurer, dies you need,scale, good reloading manual, powder,primers and brass.
__________________
NRA Life Member, SAF Member |
January 14, 2013, 01:02 PM | #4 |
Junior member
Join Date: October 3, 2012
Location: Central Texas
Posts: 1,046
|
Rock Chucker kit from RCBS. about $250.00 from Midway but google it and you'll find it for about $225.00
|
January 14, 2013, 01:11 PM | #5 |
Member
Join Date: September 7, 2010
Posts: 85
|
I started with the Lee Anniversary Reloading Kit. It's a single stage press plus primer feed and balance scale at a good price. It's a good way to find out if you really want to do this.
After a few hundred rounds, I moved up to the Lee Classic Turret, keeping the single stage press for special jobs and using the primer feed and scale (and the dies I had accumulated) with the Turret. Not long after that, I bought the powder feed attachment and an electronic scale and installed a small LED light and haven't felt a need to add anything new in a while. |
January 14, 2013, 03:04 PM | #6 |
Junior Member
Join Date: January 9, 2013
Posts: 14
|
Pistol loads are what I would be reloading. I have several from 380 to 40 with the plans to add 45 to it as well. I only once a month because of bullet prices and time restraints. thanks
|
January 14, 2013, 07:14 PM | #7 |
Senior Member
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,930
|
The Lee Classic Turret is a great press. Though I can not find one in stock anywhere online at this time.
Other than that a single stage like the Breech Lock Challenger will serve you well. If you decide you want faster, and want to upgrade then by that time there should be Classic Turrets on the shelves of sellers. Note I have been using a Breech Lock Challenger for the past 4 years. I load a minimum of 500 rounds a week. Most times it closer to 1000.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you. |
January 14, 2013, 07:23 PM | #8 |
Senior Member
Join Date: June 25, 2009
Location: Stuttgart, AR
Posts: 1,569
|
I got the RCBS Rock Chucker kit. Use everything except the lube pad. Upgraded the Uniflow with a small capacity cylinder. RCBS dies. Press is heavy duty. Approaching the 10,000 rounds loaded mark and I'm happy as a claim with my choices.
__________________
A lack of planning on your part does not necessarily constitute an emergency on my part. |
January 14, 2013, 11:19 PM | #9 |
Senior Member
Join Date: February 22, 2011
Location: Wasilla, Alaska
Posts: 228
|
I have a Hornady Lock N Load single stage press. Have used it for over 5 years with no problems. I did get tired of always having to adjust my RCBS powder throw, so bought a Lyman electronic powder measure/dispenser and it gives consistent powder weights all the time.
|
January 14, 2013, 11:25 PM | #10 |
Junior member
Join Date: December 15, 2012
Posts: 164
|
This is going to seem an ignorant question and it is. But I have zero knowledge of reloading. Are you limited to hard cast or can you get jhp bullets?
And is there a substantial cost savings to reloading or is it something you would mainly get into to be able to work up your own loads etc? Thanks |
January 14, 2013, 11:30 PM | #11 |
Junior member
Join Date: January 24, 2010
Location: South West Riverside County California
Posts: 2,763
|
"Substantial savings" come from comparing "premium" factory ammunition to your own premium version loaded with the exact bullet you want with the exact powder and powder charge you want. You can load any bullet you like. Go for a Lee Precision Classic Turret. You can use it without auto-index in single stage mode as I do. Get "Modern Reloading" by Richard Lee and Lymans 49th manuals before you do anything.
|
January 15, 2013, 12:11 AM | #12 | |
Senior Member
Join Date: January 24, 2009
Location: Anchorage Alaska
Posts: 3,341
|
Quote:
However, this setup is next to worthless if if doesn't fit your needs because you will be trading off (at a loss) most of the gear that you don't like. We can sort out a lot of what is clearly a bad fit for you only if we know you. So, please describe yourself and your needs. We can narrow your choices a little to make your decisions a bit simpler. My ideal setup that fits ME perfectly consists of the Lee Classic Turret, 6 sets of dies mounted in turrets for quick and easy die swaps, a few Auto-Disk powder measures a scale, calipers and various small tools. No guarantee it will fit YOU perfectly. Lost Sheep |
|
January 15, 2013, 05:12 AM | #13 |
Member
Join Date: December 16, 2012
Location: Blue Ridge Mtns of NC
Posts: 45
|
If you're loading straight wall pistol/revolver only, seriously consider the Dillon Square Deal B. I've been using one for more than 20 years, along side my Dillon XL 650, and it is one excellent machine. You can start out simple by loading one round at a time, similar to single stage, until you become more familiar with the process. Then move to progressive. After you get proficient with the machine 400 an hour is easily obtainable. Go to Dillon's website, and watch the video, or do a YouTube search for Dillon Square Deal B.
You still need several accessories such as, scales, calipers, bullet puller, hand-tools, etc. I can't speak for the customer service from the other manufactures, but I can for Dillon. They are excellent. Remember you get what you pay for. http://www.youtube.com/watch?v=aL1wacQrmC8 Oh yeah, you buy the Dillon, then decide re-loading isn't for you, you can sell it easily without taking a bath. Just look around, and on eBay, for what used Square Deal B's are going for.
__________________
308Prepper http://home.nra.org/# http://gunowners.org/ http://www.americanmotorcyclist.com/ Last edited by 308Prepper; January 15, 2013 at 07:05 AM. |
Thread Tools | Search this Thread |
|
|