November 11, 1999, 05:48 PM | #1 |
Senior Member
Join Date: July 26, 1999
Location: Georgia
Posts: 362
|
I'm thinking of trying Win 296 in my 44 and according to the Lee manual 25gr is the only load given for a 240gr lead bullet. Is this powder not to be reduced at all, or what? I know Hodgdon says to reduce H110 no more than 3%, and given the similarities between those two powders, does it stand to reason that the same may be applied to 296, or should I just go with the 25gr?
Thanks much, Jack |
November 11, 1999, 11:07 PM | #2 |
Senior Member
Join Date: December 17, 1998
Posts: 1,885
|
DO NOT REDUCE LOADS FOR W296! The Winchester data says this loud and clear. 296 is an excellent powder for magnum cartridges, but its real touchy about reduced loads. Check Winchester's website for more info. Sorry, I don't have the addy handy.
|
November 12, 1999, 01:11 AM | #3 |
Staff
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 16,955
|
Winchester reloading manual can be downloaded at:
www.winchester.com/reloader/index.html |
November 12, 1999, 01:42 AM | #4 |
Senior Member
Join Date: November 19, 1998
Posts: 986
|
It does no good for you, since it's second-hand as posted here, but...
I have heard at least one (only 1? I furgit sometimes...) first-had report of reduced 296 loads failing to light up and leaving a bullet lodged midway down the bore. Comparing the old Speer loading data with Winchester, the Win data appeared to be at teh 3% reduced level already. However, the fact that Win used different bullets (of the same weight) makes such suppositions dangerous. Stick with the published load. If you want less flash, blast, and velocity, use something like Alliant's Power Pistol, which *can* be downloaded from max. |
November 12, 1999, 11:51 AM | #5 |
Senior Member
Join Date: July 26, 1999
Location: Georgia
Posts: 362
|
Thanks for the help guys. I can't find a Winchester guide at any of the gun stores and I've tried to download it twice, but for some reason my computer doesn't want me to have it. I wasn't really looking for reduced loads, but starting out with a max load, per se, just goes against all the safety rules I have learned (and my ingrained desire to keep all my fingers intact!).
Jack |
November 14, 1999, 03:44 PM | #6 |
Senior Member
Join Date: November 2, 1999
Location: Chehalis, WA
Posts: 142
|
25-grains of 296 sounds a little too hot for starters, even considering that 296 is for maximum loads. Depending upon the relative hardness (or softness) of the bullet and the depth to which the design in question needs to be seated, I would start at about 22-grains and work up carefully.
|
November 14, 1999, 04:03 PM | #7 |
Senior Member
Join Date: November 2, 1999
Location: Chehalis, WA
Posts: 142
|
25-grains of 296 sounds a little too hot for starters, even considering that 296 is for maximum loads. Depending upon the relative hardness (or softness) of the bullet and the depth to which the design in question needs to be seated, I would start at about 22-grains and work up carefully.
|
November 14, 1999, 05:39 PM | #8 |
Staff
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 16,955
|
Don't know if you guys know who Randy Garrett is, but if I were you, I'd listen closely to his advice.
Good to see you here, and welcome aboard. |
November 15, 1999, 04:20 PM | #9 |
Senior Member
Join Date: March 22, 1999
Location: NY
Posts: 165
|
Garrett Ammunition no?
Joefo |
November 15, 1999, 05:12 PM | #10 |
Senior Member
Join Date: September 22, 1999
Location: Deep East Texas
Posts: 474
|
I ditto Mal H...
Welcome Mr Garrett... ------------------ "No provision in our Constitution ought to be dearer to man than that which protects the rights of conscience against the enterprises of the civil authority" - Thomas Jefferson |
November 18, 1999, 01:06 AM | #11 |
Staff Alumnus
Join Date: October 23, 1998
Location: ATL
Posts: 3,277
|
My word, the Lord is smilling on me. Mr.Garrett I am looking for a good load for my Anaconda in .45 Colt. I have tried 25 grs of 296 as per Loadbooks data with WLP primers and Hornady XTP 250 gr JHP's. Got very smokey lookin' cases after and decided to back off to 24 grs of 296. Recoil was reduced and the cases came out clean. Didn't have any pressure sign on the cases with either load. What would your recomendations be?
|
November 20, 1999, 06:27 PM | #12 |
Senior Member
Join Date: November 3, 1998
Location: Alamo, CA
Posts: 424
|
The problem with reduced loads of H-110 and W296 is a phenomenon called detonation. It is when the powder doesn't ignite in a normal way, but in some abnormal way, and this causes paradoxically high, VERY high pressures. Which can blow up guns.
Factors favoring detonation are: low loading density, reduced loads, use of regular primers where magnum primers are called for, and possibly light crimp. Win makes Hodgdon powders, BTW, and the burning rates of H-110 and W296 are very close. I spoke to a technician at Hodgdon a while ago, and he stated that the detonation phenomenon was nearly impossible to duplicate in the laboratory, but it did occur, and he had personally seen it. Win DOES list 'reduced' loads for W296 in their latest loading manual, but only for one cartridge, the .454 Casull, and the 'reduced' loads generate 38,000-40,000psi. The full loads generate 50,000psi! I would follow the advice of Mr. Garret. He makes the world's best .44 Mag ammo. Walt |
November 25, 1999, 10:05 AM | #13 |
Member
Join Date: September 14, 1999
Posts: 39
|
I've only been reloading for a couple of months now, but 44 mag with Winchester 296 is the first round I started loading. Winchester manual clearly states DO NOT REDUCE the charge and use a heavy crimp. It also states 296 is not good for light bullets. I've loaded about 2000 rounds and they've all been very accurate (much more accurate than reloads I had been buying at the range. I can actually get a group!). The Winchester manual shows some loads with 231 you can reduce. Hope this helps.
------------------ Thanks,Matt |
|
|