|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
November 6, 2000, 09:45 AM | #1 |
Senior Member
Join Date: February 12, 2000
Posts: 315
|
Just like the title says. I plan on purchasing a couple of Ruger 10/22's for my two oldest boys Christmas presents. I like to keep a barrel clean on any firearm that I own. The 10/22 has to be cleaned from the muzzle end unless a hole is drilled to accomodate cleaning with a rod from the breech. I prefer not to have a hole drilled, so I am stuck with cleaning from the muzzle with a rod, or using a bore snake or a Otis cleaning kit. Sling Shot
|
November 6, 2000, 11:05 AM | #2 |
Member
Join Date: October 1, 2000
Location: Jacksonville, FL
Posts: 43
|
I've been using the Otis kit for several years now. Sometimes I start to use a rod, but the Otis kit is so much easier, I always seem to end up using it. There's no way to reverse a brush inside the bore (a no-no), and you can clear semi-autos, lever actions and bolt actions all from the breech to the muzzle (the preferred method, though typically not practical on some types).
It comes with special slotted patches that are multi-use, but you can use standard patches with the slotted tip. I use a bore snake at the start of cleaning to get the most junk out prior to final cleaning with the Otis kit. I soak the bore with a solvent patch first, pull the snake through a few times, then final clean and oil with the Otis kit. As you can tell, I'm a fan. Dave |
November 6, 2000, 01:05 PM | #3 |
Senior Member
Join Date: January 7, 2000
Location: Idaho
Posts: 6,073
|
I use a bore snake exclusively for cleaning the bore of my 10/22 (also my Marlin Model 60). Very convenient, and seems to do a real good job. I recommend it.
|
November 6, 2000, 09:29 PM | #4 |
Senior Member
Join Date: January 19, 2000
Posts: 743
|
Yes, bore snakes really work.
There has been a lot of discussion on them in the past on this board. To summarize briefly and uncomprehensively, the majority use them at the range/in the field to clean bores that are fouling, then use regular cleaning equipment at home. There are some that don't like them and some that use them exclusively. |
November 6, 2000, 11:41 PM | #5 |
Senior Member
Join Date: April 22, 1999
Location: Chandler, Arizona, USA
Posts: 6,014
|
I have a Bore Snake for every caliber I own.
------------------ Guns cause crime like spoons cause Rosie O'Donnell to be fat! I hunt, therefore I am. |
November 7, 2000, 01:12 PM | #6 |
Senior Member
Join Date: October 13, 1998
Location: Arizona.
Posts: 853
|
I recently tried to use an Otis for removing a squibbed bullet that was barely lodged in the throat of an FAl. The defective round was factory remington hard ball .308
The Otis failed miserably, and yes, I followed the instructions. I also find it cumbersome in the field, with the multitudinous small parts and gizmos requisite to its function. I now keep a hard rod in the truck box, and carry boresnakes in the day pack. the Boresnake is faster and easier to use, and gives great results. |
November 7, 2000, 01:57 PM | #7 |
Senior Member
Join Date: September 14, 1999
Location: Indiana
Posts: 637
|
I have a bore snake for my 12 guage. It cleaned my bbl to a frightening brightness. Can't vouch for how well it would work on very heavily corroded rifled bbls, tho.
|
November 7, 2000, 06:52 PM | #8 |
Senior Member
Join Date: February 18, 1999
Location: Arizona
Posts: 2,729
|
What's a bore snake, and where on the net to see/get one?
------------------ John/az "When freedom is at stake, your silence is not golden, it's yellow..." RKBA! www.cphv.COM & www.handguncontrol.NET are being sued by Handgun Control, Inc.! See the "cease and desist" letter here: www.cphv.com/lawsuit.html |
November 7, 2000, 07:12 PM | #9 |
Senior Member
Join Date: February 12, 2000
Posts: 315
|
John: Here is a link to the boresnake. http://www.butler-creek.com/m_shooting_p.asp?grpky=232
Sling Shot |
November 7, 2000, 07:16 PM | #10 |
Senior Member
Join Date: September 14, 1999
Location: Indiana
Posts: 637
|
John/az2 -- You can find them at almost any gun store and save yourself the shipping. Even WallyMart sells them. They're about $12-15. Cool thing is they're "color-coded" so you don't mistake your .22 boresnake for your 8-guage one
|
November 7, 2000, 07:59 PM | #11 |
Senior Member
Join Date: November 4, 1999
Location: Rebel South USA
Posts: 2,074
|
I give the bore-snake a thumbs up!!! I use the traditional brush to loosen up all the deposits then run the snake through a couple of times.. VERY CLEAN INDEED!!!! I just bought a back up 30 cal snake today at Wal-Mart for $12.
|
November 8, 2000, 03:23 PM | #12 |
Senior Member
Join Date: May 29, 1999
Posts: 1,938
|
I use Bore Snake for barrels that I cannot clean from the breech side.
However, I do have a question. If one runs the Bore Snake through more than once, wouldn't once risk putting the now Bore Snake-embedded debris back into the barrel? Skorzeny ------------------ For to win one hundred victories in one hundred battles is not the acme of skill. To subdue the enemy without fighting is the supreme excellence. Sun Tzu |
Thread Tools | Search this Thread |
|
|