|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
September 24, 2012, 11:04 PM | #1 |
Member
Join Date: September 24, 2009
Location: mississippi
Posts: 23
|
Neck sizing primed .223 brass
I have purchased bulk .223 air pulled brass, bullets and powder. Bullets are .55 gr fmj and are very clean with no marks and so is the brass. Powder is WC844 and cross loads with H335. The seller states the brass needs neck sizing and I can understand that, but I have found that only about three out of a hundred will measure larger than .200 inside neck diameter. I would like to neck size all the cases but don't have a die that I like. I bought a Lee collet neck die and that was money wasted. What does the inside neck diameter need to be before seating and what die do I need for this purpose? Does anyone makes a carbide die for this purpose? I have been reloading since the 70s, but have been away from it for awhile and there are lots of products available that were not there when I was loading years ago.
Thanks for any help. |
September 25, 2012, 06:26 AM | #2 |
Senior Member
Join Date: May 30, 2007
Location: Al.
Posts: 196
|
If the necks are .200 or less ID, they'll be fine. I imagine the seller suggested neck sizing to fix any dented or out of round necks. It would have to be a bad dent before a FMJ-BT bullet would not start and seat. If you have the occasional one that is, you can use a Lee decapping rod or something similar to poke the case mouth and straighten it enough to start a bullet. Any tapered rod that will fit in the neck will work.
|
September 25, 2012, 07:52 AM | #3 |
Member
Join Date: September 24, 2009
Location: mississippi
Posts: 23
|
Neck sizing primed .223 brass
I really appreciate the help. I had consulted a few friends that load, and we had determined that we were not bringing the IND down smaller than .200, even if we full length sized. This would be (in my opinion) a wasted step, as 97% of the air pulled brass will measure this right out of the bag. You can definately feel the difference in resistance when seating the bullet and it will tell you if one is not right. The decapper pin on the Lee collet neck sizing die can not be removed, as on RCBS or Lyman, so one of the guys at Titan reloading suggested cutting it off with a dramel tool. Apparently this question had come to them before and this is what had worked for others, so this is what I did. This die should work well now on a dented neck and a replacement collet is only about four bucks. I think you will be seeing more and more questions about primed brass.
Thanks again |
September 25, 2012, 04:20 PM | #4 |
Senior Member
Join Date: June 9, 2010
Location: NEPA
Posts: 909
|
Are you sure the primers are ok?
|
September 25, 2012, 08:08 PM | #5 |
Member
Join Date: September 24, 2009
Location: mississippi
Posts: 23
|
I have tested and retested my loads and have had no problems. I have been very impressed with these components. I will be ordering more very soon.
|
September 29, 2012, 12:34 PM | #6 |
Senior Member
Join Date: December 11, 2009
Location: South Carolina
Posts: 360
|
If I am not stepping on your toes here I would soon get a new mandrel for your die.Reason for saying this is that the deprimeing pin keeps the mandrel straight for the resizing of the necks.This is the main reason to why those who use the collet die, it just puts out a straight neck when used right.
__________________
life is great but its better when you can own as many guns you wish to own.for me I haven't bought enough yet. |
September 29, 2012, 01:06 PM | #7 |
Senior Member
Join Date: May 27, 2007
Posts: 5,261
|
I have read claims of "air pulled" bullets, this air pulling of brass is most interesting and if it is as I suspect, fired ammunition, if you are loading this ammunition for a gas gun, like an AR15, you should full length resize your brass.
__________________
If I'm not shooting, I'm reloading. |
September 30, 2012, 09:31 AM | #8 |
Member
Join Date: May 26, 2012
Location: Central Florida
Posts: 78
|
Neck-sizing primed brass?
To neck-size primed brass I remove the de-capping pin from RCBS neck sizer die and "have-at-it!"
__________________
GOOD LUCK and GOOD SHOOTING!!! If you're gonna get old you better be tough;Gettin' old ain't for sissies!! |
|
|