October 23, 2012, 08:00 AM | #1 |
Senior Member
Join Date: December 29, 2010
Location: Gwinnett County Georgia
Posts: 1,136
|
Lee FCD and lead
I have heard it said that the Lee should not be used when reloading lead.
Your thoughts?
__________________
Do not follow where the path may lead, go, instead where there is no path and leave a trail - Ralph Waldo Emerson |
October 23, 2012, 08:12 AM | #2 |
Junior member
Join Date: January 24, 2010
Location: South West Riverside County California
Posts: 2,763
|
It can swage down your lead bullet. Many happy users and some don't like the FCD. More like it than not. Ranch Dog, who is going out of business, is selling a collet style aka "rifle" version from Lee Precision for handgun calibers that is well liked. I would try it and see what results you get. The handgun caliber FCD is the one that you would be referring to where some people complain about it but most don't.
|
October 23, 2012, 08:54 AM | #3 |
Senior Member
Join Date: July 8, 2012
Location: so cal
Posts: 246
|
With the FCD you have the potential to grossly deform brass and bullets if used incorrectly. In my experience with the FCD a little goes a long way.
I am sure others will will post saying what a horrible, useless die the FCD is. Don't listen, plenty of people (like me) get more than satisfactory results |
October 23, 2012, 09:02 AM | #4 |
Senior Member
Join Date: December 17, 2005
Location: Swamp dweller
Posts: 6,187
|
Follow the directions for setting up the FCD and all will be well. 20 + K of lead reloads and no issues yet.
__________________
NRA Life Member, NRA Chief Range Safety Officer, NRA Certified Pistol Instructor,, USPSA & Steel Challange NROI Range Officer, ICORE Range Officer, ,MAG 40 Graduate As you are, I once was, As I am, You will be. |
October 23, 2012, 09:13 AM | #5 |
Senior Member
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,720
|
I like having it in my tool kit for straight-wall pistol cases with cast bullets. I don't use it very often.
The one I bought for .45 Colt was a waste of money because I've never needed it -- .45 Colts have loose chambers, and an modestly-oversize bullet won't bulge the case enough to cause problems (like it will in .357, .38 Special, and .41 Mag.)
__________________
"Everything they do is so dramatic and flamboyant. It just makes me want to set myself on fire!" —Lucille Bluth |
October 23, 2012, 09:14 AM | #6 |
Senior Member
Join Date: December 3, 2011
Posts: 558
|
I have mentioned this in other threads- my FCD swages my .452" 45acp bullets by up to .001" depending on headstamp. For whatever reason the accuracy is outstanding anyway so I am not changing it. Takes a little effort pressing the cartridge into and out of the FCD but I dont argue with cloverleafs.
|
October 23, 2012, 10:48 AM | #7 |
Senior Member
Join Date: May 27, 2007
Posts: 5,261
|
I am not a fan of the rifle FCD, it swages perfectly good bullets in the middle and that is not conducive to long range accuracy
Edit: Sorry. No copyrighted material without express permission of copyright holder. See the board policy, here. The pistol Lee FCD is something else, not quite a roll crimp, not quite a taper crimp. I use the ones I have and crimp the heck out of my pistol bullets. Handguns are spitting distance weapons anyway, the furthest I shoot is 50 yards with them, I am more concerned about 100% reliable function in a handgun than what I am doing to the bullet. Maybe it makes a difference in accuracy in a handgun, but it will take something like a machine rest to find out.
__________________
If I'm not shooting, I'm reloading. Last edited by Unclenick; October 28, 2012 at 04:00 PM. |
October 23, 2012, 11:37 AM | #8 | |
Senior Member
Join Date: July 8, 2012
Location: so cal
Posts: 246
|
Quote:
|
|
October 23, 2012, 11:42 AM | #9 |
Member
Join Date: October 23, 2012
Posts: 20
|
Are you guys saying that the taper crimp is doing the swageing, or the sizer ring? Also, it isn't hard to pull a bullet after running it through this die. I've done it and still measured .452 on my boolits.
|
October 23, 2012, 12:24 PM | #10 | |
Senior Member
Join Date: December 3, 2011
Posts: 558
|
Quote:
|
|
October 23, 2012, 12:24 PM | #11 |
Senior Member
Join Date: February 7, 2009
Location: Southern Oregon!
Posts: 2,891
|
Lee offers 2 Factory Crimp Die styles. The FCD for handgun calibers is a combination "post seating sizer" and crimp die (it covers up your sloppy reloading methods). Rifle caliber FCD is a collet type die that squeezes the case evenly from the sides (I like mine for a light crimp on my .223). I gave my .44 FCD a good chance and reloaded a couple hundred rounds. The rounds with lead bullets, which previously shot fine, leaded the barrel of my Puma .44 Magnum and accuracy suffered in my Ruger SBH and S&W 629. All the jacketed ammo I made chambered nicely so a FCD wasn't needed! If you know how to adjust your dies correctly, you won't have any buldges to iron out/resize the finished round. I have reloaded thousands of .44 Magnum and Specials since '86 and .45 ACP is my most favorite for now reloading and shooting mebbe 400 per month and they all chamber and fire quite well without a FCD (9mm too!)...
jes an old guy's experience and $.04 (inflation ya know)
__________________
My Anchor is holding fast! I've learned how to stand on my own two knees... |
October 23, 2012, 12:55 PM | #12 | |
Senior Member
Join Date: October 12, 2002
Location: The same state as Mordor.
Posts: 5,568
|
Quote:
__________________
"As was the man of dust, so also are those who are of the dust, and as is the man of heaven, so also are those who are of heaven. Just as we have borne the image of the man of dust, we shall also bear the image of the man of heaven. " |
|
October 23, 2012, 05:47 PM | #13 |
Senior Member
Join Date: April 8, 2000
Posts: 2,101
|
The carbide ring is the main issue. If you have a cylinder or chamber that is a bit oversized, and your sizing your bullets bigger than normal, it can and will size the bullets smaller as the case goes through.
I picked one up for my 45acp loads and found that the ring was simply too small and every time I pushed a round into it, no matter how it was adjusted, the brass would be squeezed down around the bullets resulting in them being swedged down at least .002" or so depending on which bullets I am using, and if I actually size them before loading. This might be fine for some, and some might find no issue what so ever with theirs, but if you read enough reports on others having the identical issues when using cast, and the FCD, you can really only come to one conclusion. Personally after I popped the ring out I have not had one single issue with it since. So if you REALLY want to try one out the worst case is you "might" have to pop out the carbide ring.
__________________
LAter, Mike / TX |
October 23, 2012, 05:54 PM | #14 |
Senior Member
Join Date: December 29, 2010
Location: Gwinnett County Georgia
Posts: 1,136
|
that makes sense Mike. I am either going to quit using the FCD for cast or I'm going to buy some Dillon dies for my 550 B
__________________
Do not follow where the path may lead, go, instead where there is no path and leave a trail - Ralph Waldo Emerson |
October 23, 2012, 06:08 PM | #15 |
Senior Member
Join Date: December 1, 2002
Posts: 2,832
|
Like any other crimper, Lee's rifle FCD is fully adjustable from no effect at all to too much. Anyone wondering why they're not crimping or are damaging their bullets shouldn't look at the die, they need to look in a mirror! Not a lot of rifle ammo needs to be crimped but there is nothing else anywhere near as good or as easy to use as Lee's.
|
October 23, 2012, 07:05 PM | #16 |
Senior Member
Join Date: May 12, 2011
Location: New Mexico
Posts: 1,315
|
I use the FCD on lead with nothing but good results. The taper crimp is just fine. Semi auto rifles need the crimp or adequate neck tension to keep the COL from changing from bullet movement. Before I crimped, some .223's would slide up and engage the rifling. I don't like mixed techniques, and though I have tried intentionally loading long like that for bolt guns and single loading, I don't approve of the method for semi-auto rifles. There is a real potential for disaster.
|
October 23, 2012, 07:25 PM | #17 | |
Senior Member
Join Date: June 4, 2006
Location: West Virginia
Posts: 2,258
|
Quote:
__________________
I don't ever remember being absent minded. |
|
October 23, 2012, 09:24 PM | #18 |
Senior Member
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 609
|
The Lee FCD for hand gun rounds is a marvelous item to completely fix problems that do not exist. This is what my experience has been in my 3 years of attempting to use it.
YMMV
__________________
U.S. Army Veteran NRA Certified Range Officer |
October 23, 2012, 09:27 PM | #19 |
Senior Member
Join Date: December 3, 2011
Posts: 558
|
And there it is. I have yet to see an FCD thread on any forum that didnt include at least one "answer to a problem that doesnt exist" response.
Right on cue. |
October 23, 2012, 11:45 PM | #20 |
Senior Member
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 609
|
Held back as long as I could! I'm not sure I was in cue tho or not. Just gave my experience, after reloading my own cast bullets for 50+ years now. Thank you very much!
__________________
U.S. Army Veteran NRA Certified Range Officer |
October 24, 2012, 07:11 AM | #21 |
Senior Member
Join Date: December 3, 2011
Posts: 558
|
Haha you bet!
|
October 24, 2012, 09:55 AM | #22 | |
Senior Member
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 609
|
Quote:
__________________
U.S. Army Veteran NRA Certified Range Officer |
|
October 24, 2012, 10:03 AM | #23 |
Senior Member
Join Date: July 3, 2008
Location: middle GA
Posts: 326
|
I have a friend that uses one for all of his competition(hunter pistol) rounds. He polished his so they match his chambers. He was telling me the other day he really wished they had them when he was shooting bullseye.
__________________
Jan. 4, 2007 gasoline $2.10 gal....HMMM? |
October 24, 2012, 10:09 AM | #24 | |
Senior Member
Join Date: December 3, 2011
Posts: 558
|
Quote:
There is no right or wrong on this subject as far as I am concerned. The target cares very little how we make our loads |
|
October 24, 2012, 10:13 AM | #25 |
Senior Member
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 609
|
This next spring/early summer I'll have to ask the 10 time National Pistol Champion what his thoughts are regarding the FCD.
__________________
U.S. Army Veteran NRA Certified Range Officer |
Thread Tools | Search this Thread |
|
|