December 7, 2010, 03:53 AM | #1 |
Junior Member
Join Date: December 1, 2010
Location: Ohio
Posts: 5
|
mossbeg 500 18 in
hey yall i just picked up the home defense 18 in barrel for my mossey 500.... when i got home i noticed that it wont fit on the standard magazine tube.... is it ment for the 8 shot tube???
|
December 7, 2010, 09:59 AM | #2 |
Member
Join Date: September 18, 2010
Posts: 16
|
Define how it doesn't fit?
|
December 7, 2010, 10:02 AM | #3 |
Member
Join Date: March 13, 2010
Location: PA
Posts: 69
|
I, too, have a Mossberg 500 which I fitted with an 18-inch barrel. Mine fit. If the takedown screw is too far away from the magazine, then you may be right that is is for the 8-shot
The distance from the end of the barrel's flange that slides into the receiver to the inside edge of the flange holding the takedown screw is 15-13/16 inches on my 18-inch barrel. |
December 7, 2010, 10:13 AM | #4 |
Senior Member
Join Date: August 30, 2006
Location: Moodus, CT
Posts: 590
|
If it's an 18-1/2" barrel it's made for the standard 5 shot mag tube....
If it's a 20" barrel, then it's made for the 7 shot mag tube.... What is stamped on the barrel???
__________________
Smitty "The object of war is not to die for your country, but to make the other bastard die for his." -- Gen. George Patton |
December 7, 2010, 10:41 AM | #5 |
Staff In Memoriam
Join Date: October 31, 2007
Location: Western Florida panhandle
Posts: 11,069
|
Measure the distance from barrel tip to lug, I will do the same on mine...
The action is open when installing correct? "Capn' She won't go no further..." Brent |
December 7, 2010, 11:53 AM | #6 |
Senior Member
Join Date: December 13, 2001
Location: U.S.A.
Posts: 1,183
|
Set it next to the old barrel---if the lug spacings are even remotely close--I'd have to say operator error.
__________________
I take the leech that's bleeding me Can't stop to save my soul I take the leash that's leading me -------Metallica |
December 7, 2010, 06:07 PM | #7 |
Junior member
Join Date: June 23, 2009
Location: Orange County, CA
Posts: 2,149
|
Take a look at this barrel chart. I aam newbie to this but have been figgering out what barrels I can add to what, and I don't think there is a Mossberg 18" barrel. There is an 18 1/2" and a 20". BTW there are also Maverick 88 barrles that will fit Mossbergs. I am guessing you got a 20" barrel for a 535 Mossberg security.
http://www.mossberg.com/products/acc...section=access |
December 7, 2010, 07:46 PM | #8 |
Staff In Memoriam
Join Date: October 31, 2007
Location: Western Florida panhandle
Posts: 11,069
|
18 1/2 is called the 18.
Brent |
December 8, 2010, 10:37 AM | #9 |
Member
Join Date: September 18, 2010
Posts: 16
|
Pump it half way, line it up. There will be a 1/8 or so gap after you tighten the screw.
If you have the 7 + 1 shotgun or barrel, it won't even be close. More like 5inches difference. May just be operator error in installing. |
|
|