December 3, 2001, 08:38 PM | #1 |
Staff In Memoriam
Join Date: October 13, 1999
Location: Columbia, Md, USA
Posts: 8,811
|
Removing pad glue...
if anyone ever confused me with a gunsmith, the light must have been bad. Here's the deal.....
About 8 months ago I put a Cheek-Eez neoprene pad on my 870 TB to get a little more elevation. With an ammo change, I found out it wasn't needed. I took the thing off today and now have some glue residue on the MC part of my stock. Did I mention the wood's gorgeous? This Trapgun's of 1988 vintage, and the finish is a tough, glossy one. I suspect it to be a urethane variant.Now, the prob is to remove the glue while not messing up that finish. And I have to remove that glue, shooting a few rounds at the patterning board meant losing a few hairs in my beard each shot. Thanks in advance.... |
December 3, 2001, 09:30 PM | #2 |
Senior Member
Join Date: October 5, 1999
Posts: 408
|
There is a product called "Goof- Off" and it's for removing crayons, markers, stickers and such.
Comes in a small oil can. Primary ingredient is Xylene. I THINK it will cut the adhesive without biting into the finish... Or, how about a blast of WD40? |
December 4, 2001, 08:48 AM | #3 |
Senior Member
Join Date: January 30, 2001
Location: Texas Hill Country
Posts: 391
|
Remove the buttpad and "test" the finish there first. If the remover in question doesn't hurt the finish there it'll be safe elsewhere on the stock. Lacquer thinner will probably take the "goo"off the stock nicely
I remember reading somewhere that Remington's finish is/was an epoxy. Most stripping compounds won't touch it.
__________________
Texas - envied by lesser states since 1845 |
December 4, 2001, 11:33 AM | #4 |
Staff
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,374
|
Try good old fashioned peanut butter first.
Smear a heavy layer of peanut butter on the affected area, wrap well with saran or foil, and leave it for a couple of days in a warm area. The peanut oil seems to do a really good job at getting under glue and lifting it.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza Baby Jesus cries when the fat redneck doesn't have military-grade firepower. |
December 5, 2001, 04:25 AM | #5 |
Staff In Memoriam
Join Date: October 13, 1999
Location: Columbia, Md, USA
Posts: 8,811
|
Thanks, guys. I guess I'll Martha Stewart it and try the peanut butter mehtod first, since we have some here.
|
December 5, 2001, 03:40 PM | #6 |
Senior Member
Join Date: December 6, 1999
Location: Richmond, Virginia USA
Posts: 6,004
|
Adds new meaning to the term gun nuts.
Signed, IMSorry |
December 5, 2001, 09:12 PM | #7 |
Senior Member
Join Date: January 18, 2001
Location: Kettle Moraine country
Posts: 897
|
Dave,
If the peanut butter doesn't do it, you could try this stuff called Un-du...an adhesive remover, I read it's safe to use on fine furniture. Well, that's what the label says anyway, I have never actually tried it... I saw it on the promo shelf at a local hardware store
__________________
I knew Thomas Jefferson, he was a friend of mine...Governor Clinton, you're no Thomas Jefferson Ti faccio vedere come muore un italiano |
December 6, 2001, 08:52 AM | #8 |
Senior Member
Join Date: March 9, 2001
Location: Greenwood, SC
Posts: 874
|
I have used a product called "Goo Gone" from Walmart, Lowe's, etc.
__________________
NRA Endowment Member, NRA Certified Instructor CWP Holder US Army veteran Gunsmith www.boltandbarrel.com |
December 6, 2001, 01:35 PM | #9 |
Senior Member
Join Date: June 10, 2001
Location: western Mass.
Posts: 135
|
I have had good luck removing glue residue and labels with
WD40.. Give it a try,carefully..Shouldn't hurt the finish on a gun stock.. |
December 7, 2001, 05:51 AM | #10 |
Staff In Memoriam
Join Date: October 13, 1999
Location: Columbia, Md, USA
Posts: 8,811
|
An update....
I finally figured out that maybe I should ask the manufacturer, and gave Kick Eez a call. They recommended WD-40,and suggested a coupla applications. Worked fine. Thanks, everybody.... |
December 7, 2001, 11:31 AM | #11 |
Senior Member
Join Date: October 29, 1999
Location: Dewey, AZ
Posts: 12,858
|
Thanks for the report Dave.
Sam |
Thread Tools | Search this Thread |
|
|