|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
July 30, 2013, 04:41 PM | #1 |
Senior Member
Join Date: August 1, 2010
Location: Tampa Bay
Posts: 4,556
|
Drill press milling vise?
No room or need for a vertical mill right now (but perhaps down the road), but I could use a decent milling vise for the drill press. Primarily for some light wood milling (stock hardware) and precisely locating drill holes without spending minutes shifting/re-clamping the work.
I have a HF down the street and looked at their model- played with it a bit...and nearly ran screaming. It was as loose as a, well, you know... Any suggestions that will offer reasonable precision, that won't break the bank?
__________________
Remington 700/Savage Rebarreling /Action Blueprinting 07 FFL /Mosin-Nagant Custom Shop/Bent Bolts Genuine Cerakote Applicator www.biggorillagunworks.com |
July 30, 2013, 05:32 PM | #2 |
Member
Join Date: December 24, 2008
Location: Ohio
Posts: 78
|
I have a "Shopfox" branded one that I got at a local industrial supply. It's chinese but is pretty decent for the money and has served me well. I'd also check out "jet" tools. They are also chinese but probably the higher end and usually sold thru industrial supply houses.
|
August 1, 2013, 12:26 PM | #3 |
Senior Member
Join Date: July 18, 2008
Posts: 7,249
|
I do not have a shortage of machinist vises, problem for most, 3 of them weigh 80+ lbs. each, that much weight could turn a drill press over and no one wants that much weight on a mill.
F. Guffey |
August 1, 2013, 12:45 PM | #4 |
Senior Member
Join Date: July 18, 2008
Posts: 7,249
|
|
August 3, 2013, 02:00 AM | #5 |
Senior Member
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 4,678
|
I have used my mill ~ once a week for the last 10 years.
I have a 1963 Rockwell 21-100 vertical knee mill. I got it off Ebay.
__________________
The word 'forum" does not mean "not criticizing books." "Ad hominem fallacy" is not the same as point by point criticism of books. If you bought the book, and believe it all, it may FEEL like an ad hominem attack, but you might strive to accept other points of view may exist. Are we a nation of competing ideas, or a nation of forced conformity of thought? Last edited by Clark; August 5, 2013 at 01:07 AM. Reason: spellin |
August 4, 2013, 08:51 PM | #6 |
Member
Join Date: February 2, 2013
Posts: 83
|
Check here for a milling vise. http://www.grizzly.com/
|
August 5, 2013, 12:33 AM | #7 |
Senior Member
Join Date: April 7, 2006
Posts: 10,988
|
The Harbor Freight milling vise has adjustable gibs. When they put a floor sample together they don't tighten them up.
|
August 7, 2013, 09:34 PM | #8 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
A point against using a drill press vise for very much serious mill work is that a drill press is not made to take sideways pressure. It is made to drill, and its thrust bearing is designed to take straight line pressure. For some light work, a sturdy drill press will work OK, but under extended or heavy use, will wear off center and end up wobbling. A milling machine designed as a milling machine will be a lot better.
Jim |
August 7, 2013, 09:47 PM | #9 | |
Senior Member
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,720
|
Quote:
__________________
"Everything they do is so dramatic and flamboyant. It just makes me want to set myself on fire!" —Lucille Bluth |
|
August 10, 2013, 05:46 PM | #10 |
Senior Member
Join Date: January 24, 2011
Location: Monroe,NC
Posts: 669
|
Instead of using you drill press as a mill why dont you get a mill and use it as a drill press? Avoid the trial and error and get your self a good vise from grainger, I bought two cheap ones just to find out they didnt do the job I wanted so now I use them as a third hand on the bench and my good one on the mill.
__________________
The man that die's with the most stuff win's! |
August 10, 2013, 06:17 PM | #11 |
Moderator Emeritus
Join Date: April 27, 2013
Location: Ohio
Posts: 1,923
|
About the most you can mill on a drill press is wood, plastic, and soft aluminum. The chuck will slip on it's taper, which is most likely a Jacobs on that end. Either that, or the Morse taper may slip, but most of the time, it's the Jacobs, as it has a sharper angle. Most drill chucks aren't precisely centered either.
Another problem is the quill size, and the bearings. It is made to drill all right, but general drilling isn't that accurate. To keep it from vibrating, you need the quill all the way up, and locked. Last, wood, and plastic require a fast cutter speed, so one would be better off using a router. That leaves soft aluminum, but I doubt you will get very accurate cuts on it, as there's generally way more runout in a drill press, and way more vibration. The above is considering smaller shop drill presses, not the larger industrial versions, which are meant for machine shop applications. The ones from Delta, and others are really too weak to mill with. Last edited by Dixie Gunsmithing; August 10, 2013 at 10:01 PM. |
August 13, 2013, 11:35 AM | #12 |
Senior Member
Join Date: April 4, 2012
Location: South Jersey
Posts: 2,217
|
Look around for a used machinery dealer, auctions, ebay, craigslist and get a mill. If you find you must use a drill press than get a end mill adapter and dont use the drill chuck. http://www.shars.com/product_categor..._Mill_Adapters
I had a few endmills laying around that had a MT ground right into them. I have since scrapped them because everything here uses a collet (R-8, Cat40, etc..). Also run the drill press with the quill retracted and locked.
__________________
Concentrated power is not rendered harmless by the good intentions of those who create it. Milton Freidman "If you find yourself in a fair fight,,, Your tactics suck"- Unknown |
|
|