The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 12, 2010, 05:44 PM   #1
Qtiphky
Senior Member
 
Join Date: December 11, 2008
Location: Upper Michigan, above the Mackinac Bridge
Posts: 554
303 British

As you may have guessed by the amount of my posts today, we are snowed in here in the Upper Peninsula and I am trying out some new stuff. Never loaded this before and am looking for information. I have 150 grain Sierra Spitzers and was wondering if anyone has loaded this with Varget, Benchmark or H4895 and what were the results.

Thanks.
Qtiphky is offline  
Old December 12, 2010, 05:59 PM   #2
Lee-Enfield
Member
 
Join Date: November 29, 2007
Location: Brisbane, Australia
Posts: 29
I've had excellent results using 150gn bullets with 35gn ADI Bench Mark 2 powder. I'm not sure how that converts to what you're using, but you may find comparison charts on the ADI website.

It's a light load that is very capable out to 400 yards (the length of the range I shoot at). It doesn't stress brass too much either, which it great for 303. In fact I came first in the last 200 yard military shoot using these reloads :-)
Lee-Enfield is offline  
Old December 12, 2010, 10:53 PM   #3
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,191
ADI BM2 is sold here as Hodgdon Benchmark.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Patron Member
Unclenick is online now  
Old December 13, 2010, 09:47 AM   #4
Qtiphky
Senior Member
 
Join Date: December 11, 2008
Location: Upper Michigan, above the Mackinac Bridge
Posts: 554
Used Benchmark

I was hoping it was Benchmark as that was one of the powders listed in my Sierra manual. Loaded up with 35.1 grains and we'll see how it goes. Thanks for the replies. Now if it would ever stop snowing maybe I could get to camp to test them.
Qtiphky is offline  
Old December 14, 2010, 12:18 PM   #5
gew98
Member
 
Join Date: December 9, 2010
Location: Rural bluegrass abode
Posts: 70
I've had great luck with 4064,4895 and even 4320 and 4350. As well Accurate 2230 proved good to me as well. I have used pulled argentine 185 grain boat tailed FMJ's with I recall 36 gns of 2230 and my long range accuracy was pretty damn good in an old No4 I had. I was able to put all ten shots into a 2qt coffe can's bottom at approx 290 yds. I've got a patt'14 that tops that in accuracy and a grogeous SMLE that's a close second. Probably my two most accurate military rifles I've ever owned.
gew98 is offline  
Old December 17, 2010, 03:48 PM   #6
rbf420
Senior Member
 
Join Date: August 1, 2009
Posts: 153
I use 7.62x54r pull downs that are 150grn boat tails. as well as hornandy 150 sp. i use 37 grns of IMR-4895 and took first in a competition in promitary point last september. its a little reduced but its good to 700yrds.
__________________
My Calibers- 9mm, .38spl, .357 mag, .45 acp, 30/06, 303 brit, 7.7 jap, 7.5 french.
rbf420 is offline  
Old December 18, 2010, 02:05 AM   #7
T. O'Heir
Senior Member
 
Join Date: February 13, 2002
Location: Canada
Posts: 3,140
Slug the barrel, if your rifle is a Lee-Enfield. Their barrel IDs can vary from .311" to .315" and still be considered ok. Over .315", the barrel is shot out. Sierra makes their .303 calibre bullets at .311". If your barrel measures .313" or bigger a .311" bullet won't shoot worth beans.
"...Loaded up with 35.1 grains..." Work up the load. Don't just pick one.
__________________
Spelling and grammar count!
T. O'Heir is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:07 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07326 seconds with 9 queries