January 23, 2012, 11:07 PM | #1 |
Junior Member
Join Date: January 23, 2012
Posts: 11
|
Case shoulder cave in
Greetings,
i'm a new member to this forum and i had an issue at the range with some handloads today. my problem is with my .257 wby mag. i've been working up a load and took three loads, two different powders to the range today. shot three of each at 100 yards one looked promising. i shot two more at 300 yards and started to get high pressure signs. these loads are well under max in the book and the first three showed only a slight mark on the head. the last one i shot collapsed the shoulder in severely. i had this issues once before but i discovered that i had over charged those rounds by accident. my question is if anyone has seen this before and knows a cause. could it be something wrong with the gun itself. the cases seem to have quite a bit of soot on them after firing as well. the loads we as follows. 115gr nosler ballistic tip 67.0 gr imr 7828 115gr nosler ballistic tip 62.0 gr viht N165 115gr nosler ballistic tip 63.0 gr viht N165 this was all brand new never fired weatherby brass Shoots factory rounds without a problem Thanks! |
January 24, 2012, 05:11 AM | #2 |
Senior Member
Join Date: November 13, 2006
Posts: 8,283
|
What primer are you using?
Nosler's website said a start of 62 gr and max 66 gr with N-165 and a 115 Ballistic tip.They specified a Federal 215 Primer.That matters.It is the big fire light them up primer. I suspect you need to pressurize,expand,obturate the case more quickly to get a seal. Last edited by HiBC; January 24, 2012 at 05:34 AM. |
January 24, 2012, 12:42 PM | #3 |
Senior Member
Join Date: February 21, 2010
Location: Rome, NY
Posts: 941
|
I agree. Sounds like you are not using a magnum primer. This can lead to over pressure as well as under pressure. I know it sounds strange, but it's true even for the same load.
Pull bullets you have loaded and start over with mag primers. Standing the rifle up to get the powder on the primer might help. You really want a powder that comes close to filling the case for best results. Good luck |
January 24, 2012, 01:34 PM | #4 |
Junior Member
Join Date: January 23, 2012
Posts: 11
|
Thanks for the replies. i'm using Winchester magnum rifle primers, WLRM.
would those be good enough? i kinda started to think that maybe it was not sealing quick enough in the chamber too. previously i had press formed and shot 50 7mm rem brass in this gun. no pressure signs, still some soot though. is there a powder that might fill the cases more? |
January 24, 2012, 09:21 PM | #5 |
Senior Member
Join Date: June 17, 2010
Location: Virginia
Posts: 6,882
|
Here's what QuickLoad thinks for top-end loads:
Cartridge: .257 Weath. Mag Bullet: .257, 115, Nosler BalTip 25115 Cartridge O.A.L.: 3.170 inch Barrel Length: 26.0 inch Matching Maximum Pressure: 60000 psi Code:
Powder Wt(gr) (%Case) V(fps) Press Burn% ADI AR 2218 78.6 105 3,472 60,000 98 Vihtavuori N570 74.7 100 3,437 60,000 98 Hodgdon Retumbo 73.8 104 3,405 60,000 100 Norma MRP 2 70.2 100 3,371 60,000 100 IMR 7828 66.0 96 3,369 60,000 100 Alliant RL-25 68.3 97 3,358 60,000 100 Hodgdon H1000 70.5 101 3,356 60,000 100 Vihtavuori N170 72.5 104 3,280 60,000 96 Accurate 3100 65.4 98 3,242 60,000 100 NOTE: Calibrate on 105% case fill being right at the start of compression the N165/62/63.0gr Loads were relatively low pressure (49,000psi)-ish Were it me, I'd look real hard at using N570 and/or Retumbo. NOTE: (Starting lower than listed above until calibrated) See http://benchrest.com/archive/index.php/t-36961.html |
January 25, 2012, 02:50 AM | #6 |
Junior Member
Join Date: January 23, 2012
Posts: 11
|
as far as grouping wise the 93 gr of N165 was best. i'm not sure what the pressures would have been though, i didn't have a chrono. i plan on getting one in the near future though.
i have some H1000 that i want to try as well. i bought some federal primers today, prepped a bunch of brass and will build some more loads tomorrow. wont be a range day, its supposed to be really windy here. i also cleaned the rifle really well with "wipe out" seemed like it took about a fair bit of copper fouling. i wonder if that will help? thanks |
January 26, 2012, 02:31 PM | #7 |
Junior Member
Join Date: January 23, 2012
Posts: 11
|
so i loaded up some new rounds with federal large rifle magnum match primers. these loads we doing much better. no soot and no pressure signs. until i got near the end of my loads and one sounded funny and the next round wouldnt chamber. i looked in the bore and there was about 5 grains of unburned powder. any ideas what that could be?
thanks! |
January 26, 2012, 02:42 PM | #8 |
Senior Member
Join Date: December 13, 2009
Location: central Wisconsin
Posts: 2,324
|
If it was double base (ball) powder and you don't get the pressure high enough you'll get unburned powder in the barrel. It's much more fussy then extruded (single base) powder.
|
January 26, 2012, 04:05 PM | #9 |
Senior Member
Join Date: June 17, 2010
Location: Virginia
Posts: 6,882
|
What was the load that fizzled?
|
January 26, 2012, 07:05 PM | #10 |
Junior Member
Join Date: January 23, 2012
Posts: 11
|
it was 69.5 grains of H1000 which is a barrel shaped powder
it was the last of four loaded like that. |
January 26, 2012, 07:37 PM | #11 |
Senior Member
Join Date: July 26, 2011
Location: USA
Posts: 1,730
|
Collapsed Shoulder
The Collapsed Shoulder is in an old Speer manual. Light loads & slow powder are the cause. Use a faster burn rate of powder. Pressure is low & neck not expanding to seal. Make sure the bullets have enough neck tension. The expander should be .002" smaller than bullet diameter. This will keep the bullet from moving when the primer fires. What is your COL? The bullets bearing surface should be in full contact with the neck. If seating the bullet long to get close to the lands/rifling there may not be enough shank of the bullet in the case neck.
Last edited by 243winxb; January 26, 2012 at 09:25 PM. Reason: added Bolt text |
January 27, 2012, 05:40 AM | #12 |
Senior Member
Join Date: November 13, 2006
Posts: 8,283
|
I do not know if Weatherby still practices it,but in years past part of the Weatherby design was a substantial amount of "freebore",which,IIRC,would be removing the rifling for about the first inch plus of bore.f your Weatherby has freebore,it will be even harder to get the pressure needed to obturate the case.
I agree stepping a little quicker on the powder might be an idea.H-4831 is a bit quicker and may be worth trying. Likely its not going to work so well to stay down in the starting load range.You may need to push things closer to max,with all due caution. Please be aware that with a very high capacity case with a very small bore to let the pressure diminish,pressures can jump from moderate to too high rather quickly.Change one thing at a time and sneak up on it,but it may take a near maxload to work well. While sometimes the mfgr's tech help is a bit guarded,sometimes making a phone call to Nosler or Hogdon or whatever mfgr you are buying components from will help. |
January 27, 2012, 12:38 PM | #13 |
Senior Member
Join Date: July 26, 2011
Location: USA
Posts: 1,730
|
Weatherby Free-bore
Weatherby rifles come with about 3/8ths of an inch of "free-bore" in them to help compensate for the high pressure the factory ammunition develops. SAAMI drawing looks like about .366" for the 257. http://www.saami.org/specifications_...ex.cfm?page=CC
|
January 27, 2012, 12:43 PM | #14 | |
Senior Member
Join Date: November 8, 2010
Location: WISCONSIN
Posts: 283
|
Under-powered loadings
Quote:
__________________
OldmanFCSA = "Oldman" at www.fcsa.org FCSA Member, SCSA Member, NRA Member, & AMA Member "Oldage & Treachery will overcome Youth & Skill" |
|
January 27, 2012, 07:21 PM | #15 |
Junior Member
Join Date: January 23, 2012
Posts: 11
|
Thank you very much for the responses. i'm going to try a faster burning powder and try going a little closer to max. changing to the federal primers has helped too.
i was seating fairly long, at 3.250. i'll try seating a little shorter as well Last edited by Universeman; January 27, 2012 at 07:34 PM. |
January 27, 2012, 07:37 PM | #16 |
Senior Member
Join Date: February 9, 2005
Location: Owego, NY
Posts: 2,000
|
One thing I would do is anneal the neck and shoulder on the brass. It may be work hardened to the point it is preventing a good neck seal during firing. I shoot a few "overbore" cartridges and Retumbo works well for me. I use it in my 25-06 with the same bullet you are using. Sooty necks are not in themselves a problem but they may be an indicator of the low ignition problem. As stated before, quicker powder, hotter primer ... and annealing may solve the problem. Good luck.
__________________
,,, stupidity comes to some people very easily. 8/22/2017 my wife in a discussion about Liberals. Are you ready for civil war? |
January 28, 2012, 12:41 AM | #17 |
Junior Member
Join Date: January 23, 2012
Posts: 11
|
I'll try annealing, i actually just bought a temp stick and a torch for that purpose. most of the brass i had issues with was brand new weatherby brass though.
|
January 28, 2012, 01:02 AM | #18 |
Senior Member
Join Date: March 12, 2008
Location: Between Dallas and Shreveport, LA
Posts: 569
|
Collapsed shoulders can also be caused by ...
excess case lube when sizing the brass.
Failure to seal/obturate can be caused by forgetting to clean the lube off the sized brass when the sizing step is finished. IF THE CASE DOESN'T SEAL, IT MAY SLAM BACKWARD, CAUSING FLATTENED PRIMERS AND ejector marks on the case head-resulting in false excess pressure signs.
__________________
Artillery lends dignity to what would otherwise be but a vulgar brawl. |
February 3, 2012, 11:41 AM | #19 |
Junior Member
Join Date: January 23, 2012
Posts: 11
|
I just thought i would post an update for any that cared.
new loads are working great, no more cave ins and no more soot on the cases even. i am once again able to shoot my favorite rifle without worry! Thank you to everyone who offered advice |
February 3, 2012, 02:12 PM | #20 |
Senior Member
Join Date: April 18, 2000
Location: Metairie, Louisiana
Posts: 890
|
So what was the cause/cure?
__________________
Guns are not dangerous! People are! RKBA! |
February 5, 2012, 02:02 PM | #21 |
Senior Member
Join Date: August 3, 1999
Location: Houston, Texas
Posts: 2,991
|
I heard once that a 257 Weatherby round could be made from a standard 7mm Rem Mag round by just running it in the die for 257 Weatherby.
Have you ever tried this out of curiousity?
__________________
10mm and 357sig, the best things to come along since the 38 super! |
March 2, 2012, 10:53 AM | #22 |
Junior Member
Join Date: January 23, 2012
Posts: 11
|
sorry for the delay in response.
the problem seems to be solves, it was a combination of the case not staying expanded in the chamber for the entire process of the powder burning. or possibly a second burn. i switched to the federal LR magnum match primers and switched powders. it also really seemed to help to keep the bore really clean, and im seating the bullets further in. havent had any cases showing the pressure signs. Peter, yes i have done that. you can press form 7MM brass in a .257 wby and then load it up and shoot it. the case length is a little shorter but its not really a concern. i would also recommend annealing them after as that is quite a bit of stress on the brass. Thanks again to everyone for their help, i am once again in love with shooting my .257 wby! |
February 4, 2017, 11:10 AM | #23 |
Senior Member
Join Date: July 18, 2008
Posts: 7,249
|
If my cases collapse like the ones pictured I use faster powder, heavier bullets and or more powder. The neck did not expand and seal the chamber, gas traveled back between the chamber and case before the case sealed the chamber. And then the hot high pressure metal cutting gas got trapped between the chamber and case preventing the case fro expanding etc., and as a results; big dents. When a reloader 'almost' has it correct and worked out the case neck will turn black and carbon up. Again, a friend died, his wife gave a reloader close to 80 7 Remington Mag cases that he did not use so he gave them to me. The carbon on the necks had to be chiseled off. I then suggested we find the rifle because there was no way the neck of the case could expand when releasing the bullet. No one new who got the rifle; but we tried.
F, Guffey |
February 4, 2017, 10:04 PM | #24 |
Senior Member
Join Date: December 16, 2013
Location: Eastern NC
Posts: 3,047
|
This is a 5 year old Zombie thread.
__________________
One shot, one kill |
February 5, 2017, 09:23 AM | #25 |
Senior Member
Join Date: July 18, 2008
Posts: 7,249
|
Sniper, you are correct, when I made the additional post to the very end of the old post I thought about the comment someone made about the perfect country song. He did not agree; he did not believe the song was perfect because the song omitted words like coffee, pick-up truck, jail or prison being drunk, rain, beer, mommy, dammed or jail. And then the author of the song thought about it and added a verse or two..
It went something like: https://www.youtube.com/watch?v=jkKn5HrKgHQ Someone thought the thread was worthy of repeating on another forum so I read though the old responses and added a few verses because. And then there is that part about making additions to old threads. To make the post a box must be checked meaning checking the box means the poster is aware the post is 'OLD'. F. Guffey Last edited by F. Guffey; February 5, 2017 at 01:22 PM. Reason: add y |
Tags |
.257wby , cases , reloading |
Thread Tools | Search this Thread |
|
|