|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
December 12, 2010, 10:20 AM | #1 | |
Senior Member
Join Date: September 11, 2008
Posts: 1,931
|
Quick test to sort WW Zinc vs lead?
Is there an easy test/way to cull zinc weights?
__________________
Quote:
|
|
December 12, 2010, 10:27 AM | #2 |
Senior Member
Join Date: December 23, 2008
Location: Southern Illinois
Posts: 1,527
|
The BEST and FASTEST way is to buy a thermometer and make sure your smelt does not get much over 700 degrees. IIRC, zinc melts at just under 800 degrees (787*????) Lead generally melts around 650 ish. The Zinc WWs will float to the top of the molten lead and can be scooped out. Easy. SURE beats going through all those WWs and testing their hardness. Some people will go through and use wire cutters and gouge the lead. If it gouges easily you know it is lead. If it is substantially harder to gouge or you cant gouge it at all then it is zinc or steel. Good luck!!
__________________
~~IllinoisCoyoteHunter~~ ~NRA LIFE MEMBER~ ~NRA CERTIFIED INSTRUCTOR~ |
December 12, 2010, 10:35 AM | #3 | |
Senior Member
Join Date: September 11, 2008
Posts: 1,931
|
Bookmarked thread, thanks!
__________________
Quote:
|
|
December 12, 2010, 10:42 AM | #4 |
Senior Member
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,720
|
That works if you heat the lead slowly enough. If there's lots of steel and zinc and crap in the pot and you heat it too fast, you can get to 800 degrees at the bottom before the top is melted (zinc melts at about 780.) Don't ask me how I know that.
__________________
"Everything they do is so dramatic and flamboyant. It just makes me want to set myself on fire!" —Lucille Bluth |
December 12, 2010, 10:49 AM | #5 | ||
Senior Member
Join Date: September 11, 2008
Posts: 1,931
|
Quote:
Slow heating/melt?
__________________
Quote:
|
||
December 12, 2010, 10:55 AM | #6 |
Senior Member
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,720
|
I hand separate them somewhat; pull out the obvious Zn and Fe weights, put obvious lead weights at the very bottom. Heat slowly, and stir occasionally, and watch once there's a puddle of lead in the bottom.
The only time I got burned was when I was melting down stick-on weights and I assumed they were all soft lead. There were a *lot* of steel weights and zinc weights in there, so it just looked like it wasn't melting. Now I know better. And I have about 5 pounds of zincked lead -- too much to throw away and not enough to try to purify by fluxing with sulfur.
__________________
"Everything they do is so dramatic and flamboyant. It just makes me want to set myself on fire!" —Lucille Bluth |
December 12, 2010, 11:02 AM | #7 | |
Senior Member
Join Date: September 11, 2008
Posts: 1,931
|
Ok, I guess I can handle this. Now that it's cold and too rainy for the range, I'm getting back on track with the whole casting thang.
The guidance is appreciated.
__________________
Quote:
|
|
December 12, 2010, 07:20 PM | #8 |
Senior Member
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,969
|
Melt slow & be there ready to flux as soon as possible ,the zinc will float .
Contrary to belief a few casters of pure target shooters prefer 2/3% zinc , it makes very hard shiney bullets, just the corners not filled out sharply !!
__________________
GP100man |
December 12, 2010, 08:35 PM | #9 |
Senior Member
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,720
|
Can I safely try my zinc-lead in a Lee bottom-pour furnace (to cast some hard lead balls) or will it clog up the spout? Or poison the melter for all future alloys?
__________________
"Everything they do is so dramatic and flamboyant. It just makes me want to set myself on fire!" —Lucille Bluth |
Thread Tools | Search this Thread |
|
|