November 14, 2012, 02:33 PM | #1 |
Member
Join Date: January 7, 2008
Location: Ormond Beach, FL
Posts: 32
|
Ruger LC9 point of aim
I just got a brand new Ruger LC9, I was told at the gun shop that it had a 200 round "break in"
went to a local range and put 200 rounds through it, and it seems that it fires low, have I been doing this wrong for years? I thought the three dots were supposed to line up and it gave you the point of aim at the front sight... the gun is brand new and was test fired at the factory (or at least fired, they gave me a shell casing) it does not seem that there is any way to adjust these sights, I got a bit of what I wanted by just aiming high, but I would like for it to be fixed to the way that I "think" it should aim... |
November 14, 2012, 02:37 PM | #2 |
Senior Member
Join Date: January 9, 2011
Location: Land of the Free
Posts: 2,834
|
I shot low with mine too, but then I sold it because of those internal safeys.
|
November 14, 2012, 02:48 PM | #3 |
Senior Member
Join Date: October 2, 2005
Location: Mississippi
Posts: 398
|
I have the Ruger LCP and it seems dead on with iron sights. I do plan on adding a laser at some point just to have one.
|
November 14, 2012, 04:24 PM | #4 |
Junior Member
Join Date: April 12, 2012
Location: JOCO NC
Posts: 6
|
Truly
I owned an lc9 for 9 months and it shot with target zero (bullet hit behind front dot). I don't like my pistols set up that way. I prefer tactical zero, POI just a over front sight as it seems this is what you are accustomed to. I bought the gun from a buddy, sold it to another friend, and he recently sold it as well. The gun is not a range gun. The trigger did finally "break in" and if you let the bang surprise you I promise the bullet will go exactly where you point it. I liked it for carry but had to send it on down the road. Good luck to you.
|
November 14, 2012, 05:43 PM | #5 |
Senior Member
Join Date: June 1, 2008
Posts: 101
|
It does have a difficult trigger, but it does seem to smooth out with use.
My LC9 is very accurate when I shoot it slow fire ... Double taps ... Well I'm working on that. Also, 900+ rounds w/o a problem. |
November 14, 2012, 06:44 PM | #6 |
Member
Join Date: December 27, 2008
Location: Upstate NY
Posts: 99
|
I would try some differnt ammo. Different bullet weights will all shoot differently. Try some 115 gr, 124 gr, 147gr, etc. I'm sure you'll find some your gun likes. Also were you shooting target ammo? Try the ammo you want to carry in it for defensive purposes and see where that prints. I have an LC9 that shoots 124gr federal hydrashocks right where I'm aiming.
__________________
Joe C NRA Benefactor Member |
November 14, 2012, 07:11 PM | #7 |
Senior Member
Join Date: January 27, 2012
Posts: 1,078
|
Shooting free hand or from a rest?
It might be you. Are you anticipating recoil any? Mix in some dummy rounds with your live rounds and try it then. You may find you are anticipating recoil a little and dipping the gun slightly before it goes off. If you don't have any snap caps, try the dime drill. Put a dime flat on your front sight like forming at "T". Dryfire and make sure you are keeping the dime from falling off the front sight. If you can shoot it like that with live ammo and it is still printing below point of aim, then you can try some mechanical/ammo changes. Personally, anytime a gun doesn't shoot to where I think it should, I assume it is the shooter. (ME) I have been right about that almost every time.
__________________
I am no longer participating in gun forums. Good luck. |
November 14, 2012, 08:42 PM | #8 |
Member
Join Date: June 11, 2012
Posts: 29
|
I agree with jmfc606 about trying different ammo. My LC9 seems to shoot low with 115 and point of aim with 124 and seems to me to shoot at 6 oclock with 147 grain HPs.
|
November 15, 2012, 01:07 AM | #9 |
Senior Member
Join Date: April 19, 2012
Location: Western PA
Posts: 3,829
|
The LC9 has a very long trigger and a very long reset with a false reset along the way. This can cause many people to slap the trigger and be consistently off- target. It's still very possible the problem is the gun and not you, but I'd have someone else shoot it and see if they have the same result.
__________________
0331: "Accuracy by volume." |
November 16, 2012, 08:22 PM | #10 |
Junior Member
Join Date: December 16, 2011
Location: S. Maine
Posts: 2
|
I have owned my LC9 for a year and a half now and in the beginning had the same issue. It turned out it was my fault I have always been a single action guy and I was anticipating the gun going off and I am not recoil shy! So I mounted one of Laserlytes side mounted lasers and co-witnessed both and then just concentrating on the laser I was hitting dead on! Once I realized it was me and not the gun mastering it was easy.
|
November 22, 2012, 11:30 PM | #11 |
Member
Join Date: January 7, 2008
Location: Ormond Beach, FL
Posts: 32
|
I had a friend of mine with me for the 200 rnd break in and it seemed to shoot off a bit for him as well (however he does not shoot very often)
I will have to try this "dime test" I do have snap caps, that sounds like it may help... I have no laser, but have considered it... |
Thread Tools | Search this Thread |
|
|