March 14, 2007, 07:57 PM | #1 |
Senior Member
Join Date: March 13, 2007
Location: SoCal
Posts: 801
|
ejector mechanisms
Purchased a Rem 3200 (12g, obviously) and a Winc 101 (20g). Previous owner had removed ejector mechanisns from forearms and they are long gone ... as is he. I would like to replace. Any reasonable price. Also posted under shotguns.
|
March 15, 2007, 01:16 AM | #2 |
Senior Member
Join Date: October 20, 2006
Location: Eastern Pa.
Posts: 137
|
If you are looking for the cost of a gunsmith installing the ejectors you should get in touch with local gunsmiths. If its difficult for you to find some call the manufacturers for a price. You can also get prices from gunsmiths all over the country by posting on www.trapshooters.com They will surely answer your query. If you want to get the parts from the manufacturer, go to Barnes & Noble get the gunsmithing books pertaining to your problem check the diagrams and installation instructions and do it yourself. Hope this helps and I hope I understood what you wanted.
|
March 15, 2007, 06:53 AM | #3 |
Senior Member
Join Date: October 25, 2001
Location: Alabama
Posts: 18,533
|
Did he take out the whole "mechanism" or just the ejector springs?
A little study there could save a lot of money for parts and installation. |
March 15, 2007, 11:14 AM | #4 |
Senior Member
Join Date: March 13, 2007
Location: SoCal
Posts: 801
|
This time, unfortunately, the entire mechanism is removed from the forearm!
I have unistalled/installed the ejector mechnaisms on several guns so that is not a problem. This essentially turns the guns into extractor models that some folks prefer. Or, for folks who have tubes for their 3200. I have removed the ejector springs on several 3200s for folks who fear the common cracking of the forearm on these fine guns. Can be solved by careful drilling and pinning with fine steel or bamboo and Acraglass (or other .. suspect Gorilla Glue would work). |
March 15, 2007, 05:24 PM | #5 |
Member
Join Date: July 2, 2004
Posts: 64
|
The gunsmith we use for 3200 parts is Pat Laib, you can reach him at [email protected] or 1 320-796-2686.
__________________
simmons gun repair/law enforcement |
March 15, 2007, 10:18 PM | #6 |
Senior Member
Join Date: March 13, 2007
Location: SoCal
Posts: 801
|
Thanx. Have sent Pat an email.
__________________
"Outlaw guns and only outlaws will have guns!" Unfortunately, we may be moving in that direction. NRA Benefactor, Conservative!, VN '64-'65. Never sell a gun or a car ... and retire rich! |
March 15, 2007, 10:32 PM | #7 |
Senior Member
Join Date: March 13, 2007
Location: SoCal
Posts: 801
|
Thanx. Have sent Pat an email. But, address was rejected?????
__________________
"Outlaw guns and only outlaws will have guns!" Unfortunately, we may be moving in that direction. NRA Benefactor, Conservative!, VN '64-'65. Never sell a gun or a car ... and retire rich! |
March 16, 2007, 08:37 PM | #8 |
Member
Join Date: July 2, 2004
Posts: 64
|
well, try this one. [email protected] it might get through.
If not, i will see what i have in the shop. we build barrel sets for 3200's and have a bunch of parts.
__________________
simmons gun repair/law enforcement |
March 16, 2007, 09:33 PM | #9 |
Senior Member
Join Date: March 13, 2007
Location: SoCal
Posts: 801
|
Thanx again. Will do.
__________________
"Outlaw guns and only outlaws will have guns!" Unfortunately, we may be moving in that direction. NRA Benefactor, Conservative!, VN '64-'65. Never sell a gun or a car ... and retire rich! |
Thread Tools | Search this Thread |
|
|