|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
November 10, 2012, 06:37 AM | #1 |
Senior Member
Join Date: October 24, 2010
Location: Austin, Texas
Posts: 3,318
|
fired casings as snap caps
Will they harm a revolver's firing pin?
I have a Colt SAA in .44-40, haven't seen snap caps in that caliber. |
November 10, 2012, 08:13 AM | #2 |
Senior Member
Join Date: March 5, 2001
Location: south carolina
Posts: 435
|
striking the wasted primer shouldn't harm the pin but getting fired cases back in a cylinder might be difficult at times.
my snap caps are homemade by decapping and resizing cases and putting a piece of pencil eraser in the primer pocket
__________________
Other than That, Mrs Lincoln, How was the play? |
November 10, 2012, 08:55 AM | #3 |
Senior Member
Join Date: December 13, 2010
Location: Virginia Beach
Posts: 2,016
|
Wont harm them initially...but the spent primer of a fired cartridge will not be much use after two or three hits strikes as it will have dented and deformed to the point of being useless in the capacity of a snap cap. Snap caps have a spring or a elastic material inside of it which ensures the "faux-primer" returns to the proper depth/position to protect the firing pin.
Natchez, Brownells...even Amazon sells 44-40 snap caps.
__________________
NRA Life Member USN Retired |
November 10, 2012, 11:17 AM | #4 | |
Senior Member
Join Date: March 9, 2012
Posts: 153
|
Quote:
what adhesive did you use to keep your rubber "bumper" in the primer socket? |
|
November 10, 2012, 11:28 AM | #5 |
Junior member
Join Date: October 4, 2004
Posts: 458
|
If you are planning on doing a lot of dry firings then get a set of snap caps. I hate spending money but there are a few things where the expenditures are justified and this would be one of them. The cost is minor and they protect the firing pin. If you just want to dry fire a couple of times then a spent case is ok.
|
November 10, 2012, 04:41 PM | #6 | ||
Senior Member
Join Date: December 13, 2010
Location: Virginia Beach
Posts: 2,016
|
Quote:
__________________
NRA Life Member USN Retired |
||
November 10, 2012, 05:09 PM | #7 | |
Senior Member
Join Date: March 5, 2001
Location: south carolina
Posts: 435
|
Quote:
try it before you say it won't work. the erasers I use are the bar style cut with a plug cutter and glued in with super glue. in the old days I used the wife's nail polish as glue. sometimes I used the erasers that were designed to erase ball point pen ink but they are hard to find now a days. these home made snap caps usually last for about 85 to 100 strikes. I use em when doing a trigger job, to verify mechanics, and sometimes to get used to the pull. I am a cheap bastard and these caps are lots cheaper than store bought one.
__________________
Other than That, Mrs Lincoln, How was the play? |
|
November 11, 2012, 09:01 AM | #8 | |
Senior Member
Join Date: December 13, 2010
Location: Virginia Beach
Posts: 2,016
|
Quote:
__________________
NRA Life Member USN Retired |
|
November 11, 2012, 10:19 AM | #9 |
Senior Member
Join Date: June 24, 2010
Posts: 234
|
I use silicone in the primer pocket and it has worked out ok for me. Only about one hundred strikes and still looks good. I don't think dry firing without anything in the chamber is a problem. My experience on a civilian rifle team and in the marines has shown no problems dry firing.
|
November 11, 2012, 10:41 AM | #10 |
Senior Member
Join Date: May 17, 2012
Posts: 1,085
|
I'd imagine hot-glue would also be an easy way to fill in the primer pocket. Seems like it'd have closer consistency to the acrylic/whatever that the "official" snap caps have. It'd be real easy to repair/refill as well (and you could easily melt it out to reuse the brass as it was intended)
TCB
__________________
"I don't believe that the men of the distant past were any wiser than we are today. But it does seem that their science and technology were able to accomplish much grander things." -- Alex Rosewater |
November 11, 2012, 11:21 AM | #11 |
Senior Member
Join Date: October 24, 2010
Location: Austin, Texas
Posts: 3,318
|
I didn't know they made .44-40 snap caps, should have Googled 1st.
Oh well, thanks for the edification. I have Googled .44 Russian snap caps to no avail. Too bad as it would work in .44 special and magnum as well. |
November 11, 2012, 03:57 PM | #12 |
Senior Member
Join Date: September 3, 2012
Location: 40 miles North of Wellington, NZ
Posts: 196
|
|
November 11, 2012, 08:36 PM | #13 |
Senior Member
Join Date: April 7, 2006
Posts: 10,967
|
Hot glue, silicone and erasers offer practically no resistance to the firing pin. It will simply pierce the soft material. Don't waste your time trying it. A brass plug, siliconed in the primer pocket will work, but it's probably easier and cheaper to just buy snap caps.
And I have a lot more than 30 years of experience to back that up! |
November 12, 2012, 03:23 AM | #14 | |
Senior Member
Join Date: October 7, 2009
Posts: 995
|
Quote:
|
|
November 12, 2012, 06:58 AM | #15 |
Senior Member
Join Date: April 25, 2010
Posts: 174
|
Folks spend $400-$1200 for a weapon and then 'cheap out' on maintenance items. Sorta like my antique Corvette buddies that get the Chinesium water pumps and then wonder what happened when they fail.
|
November 12, 2012, 08:23 AM | #16 |
Senior Member
Join Date: October 17, 2000
Location: Wichita, Ks.
Posts: 426
|
Plus two, three, four.....on spending a FEW bucks on a bag of A-Zoom snap caps for dry fire practice...
Mike |
November 12, 2012, 08:35 AM | #17 | ||
Senior Member
Join Date: December 13, 2010
Location: Virginia Beach
Posts: 2,016
|
Quote:
Good point.
__________________
NRA Life Member USN Retired |
||
November 12, 2012, 09:11 AM | #18 |
Staff
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,374
|
I used a plug cutter to cut pieces out of the sidewall of an old tire and used that for my snap cap material.
Quite durable, but the tire was very hard to cut.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza Baby Jesus cries when the fat redneck doesn't have military-grade firepower. |
November 12, 2012, 05:42 PM | #19 |
Senior Member
Join Date: September 9, 2009
Location: South Florida
Posts: 1,560
|
Only problem I see with using spent rounds as snap caps it mistaking a loaded firearm for an unloaded one or vice versa...
|
November 13, 2012, 02:39 AM | #20 | ||
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,402
|
Quote:
If he's happy with the life he's getting out of his $0.03 solution, that's all that really matters. Quote:
As long as you don't put your HD revolver away with a cylinder full of fired cases, you don't have to worry about mistaking the struck primers for loaded rounds in low light, at 1 am. As for the loaded firearm being mistaken for an unloaded firearm... I think we have rules for that: 1. All guns are always loaded. Even if they are not, treat them as if they are. 2. Never let the muzzle cover anything you are not willing to destroy. (For those who insist that this particular gun is unloaded, see Rule 1.) 3. Keep your finger off the trigger till your sights are on the target. 4. Identify your target, and what is behind it. Never shoot at anything that you have not positively identified.
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
||
November 14, 2012, 12:02 PM | #21 |
Junior member
Join Date: May 16, 2008
Posts: 9,995
|
I use a spent cartridge on my 22 bolt gun. It seems to work well. Protects from chamber peening at least.
I wouldn't bother with all that for 85 shots either. If I am dry firing I could do that or more each session. My guess is I do far more as with dry firing I really just concentrate on trigger pull mechanics. |
November 14, 2012, 04:55 PM | #22 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
Years ago, I managed to find some round nylon rods in two sizes, one just right for large primers, the other just a tad oversize for small primers. I file the end a bit for the small size. They work fine for snap caps; when one looks a bit worn, I just cut another piece off the rod. The rods started out 2 foot long; I expect to have enough to last me for the rest of my life.
Jim |
Thread Tools | Search this Thread |
|
|