|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
November 8, 2015, 05:51 PM | #1 |
Junior Member
Join Date: December 11, 2014
Posts: 5
|
How badly is my barrel rusted? How to fix it? (pics)
I just moved from one part of the city to another, but didn't realize the humidity is much higher at my new place. My safe at the old place used to be 45% humidity, which never gave me any problems.
I didn't realize this until I grabbed my 308 after a few months of being here. I see what appears to be (minor?) rust, but the whole point of this rifle is for long range iron sight shooting (200 yards+ is "long range" in this context, for a 3 in target). So once again, I'm terribly worried about the effect this will have on accuracy. How badly do you guys think this will affect the rifle, after cleaning? Any suggestions on getting this stuff off? I picked up some kroil after doing some research, but wanted to ask what you guys thought before going forward with it. So far I'm, hearing I should fill the barrel with kroil for a few hours, then clean with a brass brush? You can see the results below... hoping this is not the end of this rifle's accuracy...? |
November 8, 2015, 06:15 PM | #2 |
Senior Member
Join Date: July 5, 2008
Posts: 512
|
Really doesn't look too bad. Clean it up real good with Kroil,and it probably wouldn't hurt to run some JB Bore paste through it with a cotton mop a few times. That should polish it right back up if it isn't pitted.
|
November 8, 2015, 11:38 PM | #3 |
Senior Member
Join Date: January 7, 2008
Posts: 3,224
|
It looks like nothing. Clean thoroughly, wipe the bore dry, use Break-Free CLP on the next-to-last patch, followed finally by a dry patch and done. You'll be fine.
Last edited by Pathfinder45; November 8, 2015 at 11:41 PM. Reason: Spelling |
November 8, 2015, 11:51 PM | #4 |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,390
|
Not bad. Just (temporarily) cosmetic.
Clean as usual. Finish with a light oiling (if not already using a cleaning solvent with a "preservative" oil included). Run a dry patch through it before use.
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
November 9, 2015, 10:52 AM | #5 |
Senior Member
Join Date: September 28, 2008
Posts: 10,442
|
There's really no telling until you try it.
But like the others said, it's probably nothing of concern. I once traded for a cheapie rifle with a lot more rust in the barrel than that, and it was just fine, anyway.
__________________
Walt Kelly, alias Pogo, sez: “Don't take life so serious, son, it ain't nohow permanent.” |
November 9, 2015, 11:43 AM | #6 | |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,390
|
Quote:
Two of the best shooters that I've ever owned had bores that looked like the surface of the moon - cratered, rotten, and lands rounded over so much that you could barely make them out. Neither had anything that could be called a "crown" either. ...But they didn't care. They just kept on shooting. I think I still have one of those barrels... (The action met an untimely end.)
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
|
November 9, 2015, 11:45 AM | #7 |
Senior Member
Join Date: June 20, 2008
Posts: 602
|
Get ya a goldenrod for the safe and no more problems.
http://www.safeaccessories.com/golde...fier-p-35.html |
November 9, 2015, 01:11 PM | #8 |
Senior Member
Join Date: December 5, 2007
Location: Virginia
Posts: 1,041
|
What is the humidity in your safe now ?
Are you using something in your safe to control the humidity ? |
November 9, 2015, 01:46 PM | #9 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
Have more rust in my hips than that. Give it a bath.
__________________
Spelling and grammar count! |
November 10, 2015, 03:59 AM | #10 |
Junior Member
Join Date: December 11, 2014
Posts: 5
|
Thanks a lot guys. Good to know.
I've got a 12 inch goldenrod in my 5x2x2 safe now, plus a remmington model 365 desiccant dehumdifier, and a humidity gauge -- but they don't seem to be doing anything to reduce the humidity. Any idea what could be wrong? The interior temperature is only 1 degree F higher than the exterior, same humidity inside and out. Yes, the goldenrod is plugged in... Edit: My safe humidity is currently 60%, the same as my apartment. Maybe goes up to 64% depending on the day. |
November 10, 2015, 04:55 PM | #11 |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,390
|
Make sure the safe is sealing properly, including any ports for electrical cords to pass through.
And another, or bigger goldenrod wouldn't hurt. I have the same problem. My safes don't seal properly (the doors are my problem). So, internal humidity is usually, at best and right after drying the desiccants, only 3-5% lower than external. And, I usually only get 1 degree F higher temperature inside. Sometimes, if the conditions are right and the safe hasn't been opened for a week or more, I might get +2 F indicated inside. (Mine also aren't insulated very well.) I have calibrated wireless temp/humidity sensors in each safe, above the safes, on the other side of the room at knee-level, on the back porch, and in the main living area, with the base station on the workbench in the same area as the safes. All of them can be checked directly, remotely, or even with my phone. So, it's really easy to keep an eye on what's going on without having to open the safe. ...Not that it makes much difference.
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
November 10, 2015, 05:24 PM | #12 |
Senior Member
Join Date: March 15, 2010
Posts: 8,233
|
Looks like what I call a "haze" of rust.
It will clean up fine
__________________
Woohoo, I’m back In Texas!!! |
November 10, 2015, 06:05 PM | #13 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,823
|
I doubt if it's bad at all. Even a pitted bore can produce good groups. Shoot it and find out.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
Thread Tools | Search this Thread |
|
|