November 12, 2012, 10:43 PM | #1 |
Senior Member
Join Date: June 28, 2011
Location: Oregon
Posts: 160
|
Berry's .38 Bullet Issue
Greetings.
I have had issues with Berry's in the past regarding this, so I don't know why I keep going back to them...except their cheap. I'll cut to the chase: I bought some (2,000) .38/.357 double struck, 158 grain, round nose bullets. They measure .355" in diameter. Is this too small of a diameter? The problem is that they are just too loose in the cases. I have Zero and Hornady brand bullets; they measure .357" and/or .358" in diameter and seem to work fine--nice and snug in the cases. I've used other Berry's bullets and they work fine, but I always seem to have sizing issues with their .38 bullets. One gent suggested using a 9mm sizing die...and I did on my last batch...worked just fine. But on this new batch, they're loose, even with using my 9mm sizing die. Is .002" too little to be worried about, and if so, why are the slugs too loose in the cases (before belling the mouth of the case). Thanks in advance for replies. Uncle Loodis (but you knew dis) |
November 12, 2012, 10:48 PM | #2 |
Senior Member
Join Date: December 10, 2005
Location: Central , OR
Posts: 1,888
|
I have not used Berry's but I have used Rainier and Xtreme bullets with good results.
|
November 12, 2012, 10:59 PM | #3 |
Senior Member
Join Date: June 28, 2011
Location: Oregon
Posts: 160
|
I haven't used Rainier but I have used Zero and Xtreme with good luck too. I don't know why I keep screwing around with Berry's. Thanks for the info.
U.L. |
November 12, 2012, 11:01 PM | #4 |
Senior Member
Join Date: January 6, 2008
Location: Northeast Colorado
Posts: 1,993
|
The 125 gr .357 diameter Berrys bullets I have used are fine. One time I bought a box of Speer that were .355 diameter. Still have that box as that diameter is appropriate for 357 Sig.
|
November 12, 2012, 11:04 PM | #5 |
Senior Member
Join Date: June 28, 2011
Location: Oregon
Posts: 160
|
I have some 125 grain flat points too from Berry's...they are .357" in diameter. I am thinking of contacting Berry's and seeing if they'll take their .355" bullets back for a refund. It really irritates me too...I was in the mood to start cranking out .38 Spl. tonight!
|
November 13, 2012, 05:20 PM | #6 |
Senior Member
Join Date: February 7, 2009
Location: Southern Oregon!
Posts: 2,891
|
Yep, .355" is too small for .38/.357. Ok for 9mm, but even for a jacketed bullet, .355" is too small.
__________________
My Anchor is holding fast! I've learned how to stand on my own two knees... |
November 13, 2012, 06:27 PM | #7 |
Senior Member
Join Date: June 9, 2010
Location: NEPA
Posts: 909
|
Sounds like they sent you 9mm bullets!
|
November 13, 2012, 08:35 PM | #8 |
Senior Member
Join Date: June 28, 2011
Location: Oregon
Posts: 160
|
Update
Well, I contacted Berry's--emailed them last night and then followed up with a phone call this afternoon. They asked me to send a couple of bullets from each of the three lots, so I put some in three different ziplock bags with a slip of paper in each--that listed each bag's lot number. I am going to UPS them to Berry's. Their phone help is at least polite, and seemed concerned about the issue. I will post another update when I get a reply from them.
U.L. |
November 15, 2012, 09:44 AM | #9 |
Senior Member
Join Date: May 26, 2008
Posts: 472
|
I have had the same prob with the 38 Super bullets from Berry's -.355, just too loose in the case, am going to try to put more taper crimp on them so I can at least use them
|
November 15, 2012, 01:54 PM | #10 |
Senior Member
Join Date: July 23, 2006
Posts: 356
|
I prefer and use Xtreme -- these are highly recommended. I get much better accuracy from them than from others.
willr |
November 15, 2012, 02:23 PM | #11 |
Senior Member
Join Date: March 13, 2009
Posts: 107
|
Did they weigh 158 gr?
|
November 15, 2012, 02:25 PM | #12 |
Junior member
Join Date: December 10, 2006
Location: NC
Posts: 365
|
Last year I had an issue with Berrys being mislabled. I ordered several boxes and one came to me labeled as 40 cal, 200 grain when they were actually 44 cal, 200 grain. I called to alert them and they seemed thankful for the heads up.
|
November 16, 2012, 09:13 AM | #13 |
Senior Member
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,723
|
I just bought a 1K box of the exact same bullet the OP posted about and this thread got me concerned, so I miked a few of them and most were right on at .3570, with a few coming in at .3565. My guess is that UncleLoodis got a box of 9mm bullets that somebody at Berrys put a .38 label on, but 89blazin had the $64K question: Are they actually 158 gr? Berrys doesn't (and I wouldn't expect them to) list a 158 gr bullet in 9mm, so if they're 158 gr then they're presumably .38 bullets that got sized incorrectly.
__________________
NRA Benefactor Life Member NRA Certified Instructor: Rifle, Pistol, Shotgun, PPIH, Metallic & Shotgun Shell Reloading; RSO Pemigewasset Valley Fish & Game Club |
November 16, 2012, 03:56 PM | #14 |
Senior Member
Join Date: July 28, 2007
Location: Ohio
Posts: 11,756
|
I'd think any operation could have some screw-ups like this and I can see where it would cause quite a bit of grief! I've often wondered about HEAVIER bullets getting mixed in with some lighter-for-caliber ones, and how that could create a potential over-pressure event in some loads...but then I figured that I'd have to have been failing in my part to not notice a significantly longer slug.
In any case, I've bought more Berry's plated bullets than perhaps the average buyer does and I can truthfully report that I've never gotten anything that was mislabeled or otherwise out of whack. Even the rare occasion when they've offered some manner of a "blemished" lot, I've been completely happy with those, too. I've gotten them from at least 5 different sources, too. I've dealt with Berry's a couple of times and they are a fine group with a great product that I continue to use an exorbitant amount of.
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss. |
November 17, 2012, 01:53 AM | #15 |
Senior Member
Join Date: November 28, 2007
Posts: 302
|
How are you measuring the bullets? Are you using a micrometer or a set of calipers? A mike is probably the better way as a caliper can be a bit inaccurate.
|
November 26, 2012, 11:55 PM | #16 |
Senior Member
Join Date: June 28, 2011
Location: Oregon
Posts: 160
|
thanks
First off, thanks for all the replies. I really do appreciate you all taking the time to reply and offer help.
Berry's did call me. They said that they measured the bullets I sent back and they were at .357. Now, I measured each bullet of the about 15 I sent back and they were NOT .357. I zero'd out my digital mike and measured and remeasured them. Yes, they weighed 158 grains, with a super small amount of wiggle room. I would second guess my measuring, except I have some Hornady XTP and some Zero JHP bullets, BOTH of which work just fine and dandy in the SAME cases I tried with the Berry's bullets. Again, even using a 9mm sizing die, the Berry's were loose (pre belling the mouth). Anyway, the guy at Berry's was very polite but stuck to his story. So I told him I'd like to return them. He said to just send them back and he would credit my CC that I used to order them. I just ordered 5K Zero brand from Roze Distrib. I've used them before and have had NO problems with them...and the ones I ordered are FMJ, so I don't have to be concerned with FPS (not that I usually load them hot enough to worry anyway). So, I probably won't be ordering any more .38/.357 bullets from Berry's. I may order .45 Auto or 9mm...but not .38/.357. Thanks again for your replies. Uncle Loodis |
November 27, 2012, 12:10 AM | #17 | |
Senior Member
Join Date: December 10, 2005
Location: Central , OR
Posts: 1,888
|
Quote:
|
|
November 27, 2012, 02:37 PM | #18 |
Senior Member
Join Date: July 28, 2007
Location: Ohio
Posts: 11,756
|
I can tell you that Nosler makes some very nice handgun bullets and their attention to detail is obvious...and reflected in their price. However, they are amongst the SLIMMEST handgun bullets I've ever tried, and I had to discontinue their use in 10mm because I simply wasn't happy with the case mouth tension I get with them.
And I suppose you could reference some manner of technique or operator error, but that would fly in the face of the some 4,850 other top-notch 10mm handloads I've concocted with bullets manufactured by at least six different companies and sent downrange in four different handguns... so my experience tells me it was the Nosler slugs. I went through 750 of them in 10mm -- and still use them in .44 Magnum.
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss. |
November 27, 2012, 03:49 PM | #19 |
Senior Member
Join Date: September 10, 2008
Posts: 370
|
I've only used Berry's once many years ago, .355 hollow point @ 124 grains. Plating must be much thinner than the Rainier bullets I currently use. At 9x19mm velocities the Berry's bullets keyholed, will never use again.
__________________
"THE CONSTITUTION ONLY GIVES PEOPLE THE RIGHT TO PURSUE HAPPINESS, YOU HAVE TO CATCH IT YOURSELF." ~BENJAMIN FRANKLIN. |
November 27, 2012, 04:11 PM | #20 |
Senior Member
Join Date: October 14, 2009
Location: Sunshine and Keystone States
Posts: 4,461
|
I've used 4K+ Berry's 115 gr. plated bullets in 9mm and have never had a problem. I also used 500 or so 125 gr. plated .38 special bullets and had no problems either, although I now only use lead bullets.
|
November 27, 2012, 04:21 PM | #21 |
Member
Join Date: August 31, 2012
Posts: 39
|
I had some Berry's Hp for 357 and were okay but about 5 of them when I went to put them on the brass to seat fell down inside the case.
|
November 28, 2012, 03:30 PM | #22 | |
Senior Member
Join Date: July 28, 2007
Location: Ohio
Posts: 11,756
|
Quote:
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss. |
|
November 29, 2012, 10:58 AM | #23 |
Senior Member
Join Date: November 18, 2010
Location: Boise, ID
Posts: 131
|
I've been using the Berry 158 gr. RNF bullet in my 357 mag target/plinker loads and haven't had any problem with them at this time. I did order some of their 150 gr. RNF bullets for my 30-30 and had a similar problem as UncleLoodis. I have never had a problem with lack of neck tension loading for 30-30 Win until I loaded the 30-30 bullets from Berry. Many of the bullets could be pushed into the case with hand pressure on the bullet. I got my mike out and measured 50 random bullets out a box of 250. I found of the 50 I measured 20% were smaller than .308. These bullets were not mis-marked they were mis-manufactured. I neck size my 30-30 cases using the Lee Neck Sizing Die and solved the problem by reducing the size of a spare mandrel for the die. This allowed me to size down the case enough to grip the bullet. It looks like they may be having some quality issues. Just my experience with them.
Cary
__________________
Shooters. We are a community. United we stand divided we fall. |
January 14, 2013, 11:04 PM | #24 |
Senior Member
Join Date: June 28, 2011
Location: Oregon
Posts: 160
|
Well it's about time
I just thought I'd update this.
I returned the bullets in NOVEMBER. On January 9th, I FINALLY received a credit from Berry's. They decided to charge me a 10% restocking fee, and still claim that there was nothing wrong with their bullets. And, they will not refund my postage. If you read the posts, I spent my time to separated and tag bullets from each lot number in order to assist them with their issue. In return, I get no thanks, no credit for the roughly $22.00 in postage, and a 10% restock fee. I WILL NEVER, EVER, give them one cent more of my business. One does not treat customers this way and expect repeat business. Sincerely, Uncle Loodis |
January 15, 2013, 03:44 PM | #25 |
Member
Join Date: March 4, 2012
Location: Johnson City, TN
Posts: 70
|
In our internet, instant communication world of today, the masses can learn about poor products or service instantaneously, so if anyone wants to succeed in commerce or in a profession, he had better treat every customer or client the way he would want to be treated, or even better.
__________________
ZOOM 2X, pronounced "ZOOM ZOOM", is the tag on my supercharged, etc. Miata. NRA Benefactor |
Thread Tools | Search this Thread |
|
|