|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
January 6, 2005, 07:04 PM | #1 |
Junior Member
Join Date: January 6, 2005
Posts: 2
|
In need of Remington Nylon 66 Disassemble & Reassemble Help!
I disassembled my Nylon 66 so I could clean it and now I cannot get it back together. If anybody has any advice or even a schematic/picture or anything that might help I would really appriciate it.
Please email me at [email protected] |
January 7, 2005, 06:20 AM | #2 |
Staff In Memoriam
Join Date: January 8, 1999
Location: Brunswick,GA USA
Posts: 1,884
|
unable to send to hotmail. Inbox too small
HJN |
January 7, 2005, 07:29 PM | #3 |
Junior Member
Join Date: January 6, 2005
Posts: 2
|
Sorry
|
January 11, 2005, 06:35 PM | #4 |
Junior member
Join Date: January 9, 2005
Location: SC.
Posts: 65
|
My Dad has had one for 40 yrs ? or so. Never cleaned. I didn't even know how to take it apart. I e-mailed Remington and they sent me a copy(print) of the original book to my home address. Man was that thing DIRTY! I t still fired like a champ before being cleaned though.
|
February 18, 2005, 12:34 PM | #5 |
Junior Member
Join Date: February 18, 2005
Posts: 7
|
Remington Nylon 66/Apache 77
I just obtained an old Remington Apache 77 22 autloader (like a Nylon 66 but with a clip, apparently a special run made for K-Mart) although the clip is missing.
I'd apreciate any disassembly/assembly instructions because it appears a little bit of special knowledge would help. Thanks, Clive, <[email protected].> |
February 19, 2005, 02:33 PM | #6 |
Junior Member
Join Date: February 18, 2005
Posts: 7
|
Re. Remington Apache 77
Thanks for the inf. Harley. Now I can probably put it back to together although on inspection, it's not dirty or gummed and has hardly any wear.
I went to the gun stand at the local flea market today on the off chance of replacing the missing clip. Not only did they have several NOS Remington ones, they had a choice of 5 and 10-shot. (BTW, the 77 has a clip whereas the 66 uses a tube.) Nice to know these old nylon Remingtons are so well regarded. Certainly a gun worth saving. |
March 12, 2005, 10:44 PM | #7 |
Junior Member
Join Date: March 12, 2005
Posts: 2
|
I need these directions as well.
|
March 14, 2005, 12:12 AM | #8 |
Junior Member
Join Date: March 12, 2005
Posts: 2
|
Thanks recieved the e-mail, i spent almost three hours yesterday, trying to figure it out.
|
March 14, 2005, 06:26 AM | #9 |
Senior Member
Join Date: February 16, 2005
Location: Charleston, WV
Posts: 302
|
Just a comment on the Nylon, I had a friend years ago who's father had one.
We used to take it out and shoot it, a lot! To my knowledge, that gun had never been cleaned since it was new! I never knew of it ever jamming or failing to fire. Just goes to show ya, they don't make 'em like they used to, even the cheapest of guns in those days are better than the "premium" guns today! |
March 21, 2005, 11:44 AM | #10 |
Junior Member
Join Date: March 21, 2005
Posts: 2
|
Nylon Apache 77 assembly help
Am in need of assembly help with Remington Apache 77. Does anyone know where I can get a diagram? Or can anyone help? Please and Thanks Deb [email protected]
|
March 22, 2005, 05:43 PM | #11 |
Senior Member
Join Date: February 16, 2005
Location: Charleston, WV
Posts: 302
|
Just FYI,
You can call, or write to Remington, they will send you a copy of the manual that came with your gun. I did several years ago, and they send me one that got here in just a few days. |
March 22, 2005, 09:38 PM | #12 |
Junior Member
Join Date: March 21, 2005
Posts: 2
|
Remington Apache 77
Thanks. I will give that a try. Hopefully it will have detailed assembly info.
Thanks again Deb |
March 29, 2005, 03:20 PM | #13 |
Junior Member
Join Date: March 29, 2005
Location: Texas
Posts: 1
|
Nylon 66 info
Folks, I'm in the same boat as most of you "were"....I picked up my dad's Nylon 66 and want to clean it up some (probably been 10yrs or more since it's been "opened up") but don't wanna do it w/o some sort of schematic/breakdown. Could someone please send it to me or tell me how to get it ?? Thanks a bunch, and by the way, I really like the site I'm more of a Mil-Surp shooter but this site is fantastic and hope to do some listenin' and learnin' in here as well....Thanx again, Marty
|
April 3, 2005, 05:04 AM | #14 |
Junior Member
Join Date: March 15, 2005
Location: Oklahoma City
Posts: 10
|
Nylon 66 breakdown
Hate to just pile on, but I would appreciate a copy of the Nylon 66 disassembly instructions. Same as everyone, my dad has one that has never been cleaned.
Thanks, Mike [email protected] |
April 3, 2005, 05:36 AM | #15 |
Staff In Memoriam
Join Date: January 8, 1999
Location: Brunswick,GA USA
Posts: 1,884
|
Mike:
Sent by separate email HJN |
April 3, 2005, 08:43 AM | #16 |
Senior Member
Join Date: December 2, 2004
Location: Murderapolis
Posts: 521
|
__________________
Tom. |
April 12, 2005, 04:32 PM | #17 |
Junior Member
Join Date: April 12, 2005
Posts: 1
|
|
April 12, 2005, 08:23 PM | #18 |
Junior Member
Join Date: April 27, 2002
Posts: 8
|
On the way.
|
April 28, 2005, 09:54 PM | #19 |
Junior Member
Join Date: April 28, 2005
Posts: 1
|
I'm looking for the instructions as well. My father just gave his to my 12 year old son. He took good care of it and insists my son does also. Wish he would have passed it to me when I was 12.
Could someone forward to me at [email protected] |
April 30, 2005, 06:33 PM | #20 |
Junior Member
Join Date: April 30, 2005
Posts: 2
|
Hey if someone wouldn't mind I would like to get those disassemble and reasemble instrctions also.
[email protected] |
June 21, 2005, 03:27 PM | #21 |
Member
Join Date: June 21, 2005
Location: Pascagoula MS
Posts: 34
|
have a Remington Nylon 77 and was wondering if I could also get the assembly/dissasembly instructions.
|
July 3, 2005, 02:39 PM | #22 |
Junior Member
Join Date: July 3, 2005
Posts: 1
|
disassembly instructions
I'm having the same problem as everyone else. I managed to get the barrel off but can't seem to remove the bolt/upper assembly. I would greatly appreciate theese instructions as well. thanks
[email protected] |
July 4, 2005, 03:47 AM | #23 |
Staff In Memoriam
Join Date: January 8, 1999
Location: Brunswick,GA USA
Posts: 1,884
|
Stupid tom:
Sent by separate email HJN |
July 4, 2005, 07:50 PM | #24 |
Senior Member
Join Date: February 5, 2002
Posts: 1,819
|
Mr. Nolden,
PM sent sir. In the interim I'm getting a "selection" of ammo to be tested...
__________________
Use Enough Gun TFL Alumni |
July 10, 2005, 12:25 PM | #25 |
Junior Member
Join Date: July 10, 2005
Posts: 1
|
Need Help with my Nylon 66
I need help finding instructions to dissasembly of my Nylon 66.
Just retrieved from my son after about 25yrs and found the firing pin retracting spring and retaining pin missing. Need to know how to disassemble and put in the new parts. |
Thread Tools | Search this Thread |
|
|