February 10, 2002, 04:01 PM | #1 |
Moderator Emeritus
Join Date: June 15, 1999
Location: Ohio
Posts: 7,558
|
Removing Surface Rust
I recently picked up a used shotgun which has some surface rust on the barrel. I would like to remove this rust without destroying the blued finish. Is this possible, or is the finish already ruined if there is rust present?
I've heard of an old trick of using a penny to scrape off the rust, but am unsure of actually doing it as I don't want to damage the finish. Has anyone else ever done this with a penny? Can you use a section of curved copper pipe instead? What sort of lube/solvent should I use while scraping it? Thanks! |
February 10, 2002, 04:10 PM | #2 |
Senior Member
Join Date: February 6, 2001
Location: NE OH.
Posts: 828
|
For light surface rust, I use some 0000 Steel Wool & gun oil. It will remove the rust & doesn't seem to hurt the finish. But if the gun is pitted....it will still be pitted.
__________________
...arms...discourage and keep the invader and plunderer in awe, and preserve order in the world as well as property. ...Horrid mischief would ensue were (the law abiding) deprived the use of them. --Thomas Paine |
February 10, 2002, 04:47 PM | #3 |
Senior Member
Join Date: August 10, 2000
Location: WI
Posts: 1,395
|
Try a brass brush and Hoppe's first, if it's not too deep that will get it out. If that doesn't get it, go for the steel wool.
__________________
A plan is just a list of things that doesn't happen. |
February 11, 2002, 03:38 PM | #4 |
Moderator Emeritus
Join Date: June 15, 1999
Location: Ohio
Posts: 7,558
|
Thanks for the responses. I'll probably try the brass brush method first.
Anyone have experience with the penny idea? |
February 12, 2002, 11:31 AM | #5 |
Senior Member
Join Date: April 25, 2000
Location: Mass - the cradle of liberty!!
Posts: 106
|
I pefer to use bronze wool (get from any marine store) as it leaves no steel residue that can oxidize. Plus it's softer, so you're not as likely to ruin any finish ...
|
February 12, 2002, 01:03 PM | #6 |
Senior Member
Join Date: October 29, 1999
Location: Dewey, AZ
Posts: 12,858
|
I like to wet it down with Break Free, let sit over night, re-wet and remove with soft cloth. Break Free disolves a lot of rust. Be carefull as the loosened rust is abrasive and can mar the unrusted finish surrounding the area.
If that fails, then get more agressive as in above posts. Good luck. Sam |
February 12, 2002, 03:17 PM | #7 |
Senior Member
Join Date: October 11, 1999
Location: One of the original 13 Colonies
Posts: 2,281
|
If the breakfree fails try some Flitz metal polish applied gently and then after drying removed with a soft cloth.
It worked for me on the backstrap of a model 36 i bought used, and did not remove the bluing. |
February 12, 2002, 04:51 PM | #8 |
Senior Member
Join Date: October 29, 1999
Location: Dewey, AZ
Posts: 12,858
|
Thanks Master.
Sam |
February 12, 2002, 09:01 PM | #9 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
I agree on bronze or brass wool, but you don't need to find a marine store, just the cleaning section of your local super market.
Jim |
|
|