February 4, 2013, 03:47 PM | #1 |
Member
Join Date: September 26, 2011
Posts: 21
|
Barrel threader
I hail from Kansas and am lookin for someone to thread a 700 sps tac for a brake. Anyone got any local suggestions?
Thanks Keith |
February 4, 2013, 08:12 PM | #2 |
Senior Member
Join Date: January 24, 2011
Location: Monroe,NC
Posts: 669
|
If you cant find a smith local any good machine shop should be able to do it. Get your break and take it with you. depending on the cal. it will be 1/2x28 or5/8 x 24 unless you have something larger than 30 cal.
__________________
The man that die's with the most stuff win's! |
February 5, 2013, 10:13 AM | #3 |
Member
Join Date: September 26, 2011
Posts: 21
|
Anyone have any experience with these brakes?
|
February 6, 2013, 01:56 PM | #4 |
Member
Join Date: August 23, 2006
Location: Los Angeles, CA
Posts: 53
|
I have done a bunch of them, but I am in Los Angeles, not Kansas.
You will probably end up having to send it off to someone. Beware of local machine shops because while they might do the job, it might not be correct if you don't tell them everything that needs to be done and what is important. The threads need to register off the center of the bore, not the outside of the barrel. They most likely won't have an action wrench to pull the barrel, or a back-side spider on the headstock, or a headstock short enough to hang the barreled action out the backside of the headstock. If they shove a center into the muzzle, make sure they re-cut the crown afterwards. A proper gunsmith is the way to go as they should understand all the pertinent details. |
February 8, 2013, 11:47 AM | #5 |
Member
Join Date: September 26, 2011
Posts: 21
|
Any one used muzzlebrakesandmore . Com?
I've found some one to thread the barrel. Now just to choose a brake. |
February 8, 2013, 12:43 PM | #6 | |
Senior Member
Join Date: June 16, 2008
Location: Wyoming
Posts: 11,061
|
Quote:
THEY WORK. They do reduce recoil dramatically. My 300 WM has a heavier brake and its not much worse then my 257 Roberts in the recoil department. I put a smaller brake (not so heavy duty) on my 375 because I didn't want to add a lot of weight since its a hunting rifle. It now recoils about like a 30-06. Even on lighter rifles like 22s, 223s, etc they work, they eliminate a lot of muzzle jump. You will need to make sure you wear ear protection, which would be stupid if you don't use them with or without brakes. The brake is going to come with a small hole which should be enlarged for your caliber when its installed. That makes sure its lined up with the bore. Make sure you tell your gunsmith to bore it .20 over size. Meaning if you are putting the brake on a 308 it needs to be bored .0328. Larger is OK, but never smaller. Screws up your accuracy when the bullet bounces off the side of the brake. Some smiths will try to bore the brake smaller, DON'T LET THEM, go with the Brake Manufacture recommendations. Like I said, they work, now I'm lining up more of my rifles for brake instillation.
__________________
Kraig Stuart CPT USAR Ret USAMU Sniper School Distinguished Rifle Badge 1071 |
|
February 8, 2013, 11:17 PM | #7 |
Member
Join Date: September 26, 2011
Posts: 21
|
Thank you bud. I plan on gettin one next check.
Keith |
February 9, 2013, 03:00 PM | #8 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,024
|
I think Kraig typo'd and meant 0.02" over, so his second number is correct.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
February 9, 2013, 08:23 PM | #9 |
Senior Member
Join Date: June 16, 2008
Location: Wyoming
Posts: 11,061
|
I think you are right. .02 over bore, so for a 308 it should be .328.
Sorry.
__________________
Kraig Stuart CPT USAR Ret USAMU Sniper School Distinguished Rifle Badge 1071 |
February 10, 2013, 10:26 AM | #10 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,824
|
I'd send it to Trinidad Colorado for the gunsmithing school's machine shop instructor to do. I've seen a rifle he put a muzzle brake on and it was hard to see where the brake began and the barrel ended. PM me if you want his contact info.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
February 10, 2013, 11:36 AM | #11 | |
Senior Member
Join Date: March 26, 2005
Location: Osborn, Missouri
Posts: 2,697
|
Quote:
Best Regards Bob Hunter www.huntercustoms.com |
|
February 11, 2013, 09:56 PM | #12 |
Senior Member
Join Date: December 10, 2012
Posts: 6,161
|
I use a rifle builder who both makes the brake and installs it.
|
Thread Tools | Search this Thread |
|
|