The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Bolt, Lever, and Pump Action

Reply
 
Thread Tools Search this Thread
Old December 25, 2012, 08:30 PM   #1
C/O
Senior Member
 
Join Date: December 8, 2004
Posts: 232
3-9X40 scope?

I received a new Bushnell 3-9X40 scope for Christmas from my dad. He got it to replace the cheap Tasco scope on my Marlin 30-30.

My question is, once it is sighted in, will zooming it in maintain zero or will the point of aim be changed?

Sorry if this is a stupid question, but I am just now getting into rifles.
C/O is offline  
Old December 25, 2012, 08:37 PM   #2
mehavey
Senior Member
 
Join Date: June 17, 2010
Location: Virginia
Posts: 6,869
It should retain zero as it zooms.
(At least that's the design intent)
mehavey is offline  
Old December 25, 2012, 08:56 PM   #3
C/O
Senior Member
 
Join Date: December 8, 2004
Posts: 232
Thanks. Like I said, I am just now getting into long guns. All my exp. has been with handguns. I have had a couple rifles, but never messed with them much.
C/O is offline  
Old December 25, 2012, 09:17 PM   #4
C/O
Senior Member
 
Join Date: December 8, 2004
Posts: 232
I am starting to think the scope may be to much for my rifle which is a Marlin 336 30-30. The 30-30 is not listed in the ballistic charts for the Bushnell DOA 600. Opinions?

Last edited by C/O; December 25, 2012 at 09:23 PM.
C/O is offline  
Old December 25, 2012, 09:27 PM   #5
603Country
Senior Member
 
Join Date: January 6, 2011
Location: Thornton, Texas
Posts: 3,995
Probably most folks wouldn't feel like they needed a 3-9 on their 30/30, but there's no crime in doing it. Most of my lever action years were with a straight 4 power, but I'd have used a variable if I'd had one. Your effective range with that rifle is probably 150 to maybe 200 yards, so sight it in for 150 and don't worry about the BDC lines or dots.
603Country is offline  
Old December 25, 2012, 09:39 PM   #6
PawPaw
Senior Member
 
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,137
Quote:
It should retain zero as it zooms.
(At least that's the design intent)
That's the intent, but in actual practice, your mileage might vary. I kow that I've seen small changes in POA as the magnification changes. I have scopes on two of my .30-30s. One, an old 2.5 bushnell, on the other, a 4X Nikon. There's nothing inherently wrong with a 3X9 on a .30-30, but for my purposes that's too much scope. Still, if you like it, go for it.
__________________
Dennis Dezendorf

http://pawpawshouse.blogspot.com
PawPaw is offline  
Old December 25, 2012, 09:41 PM   #7
C/O
Senior Member
 
Join Date: December 8, 2004
Posts: 232
Are all 3-9 scopes this way? I like the idea of the variable scope, but would like one designed more for the 30-30 round. What do you suggest?

If I sight the one above at 100yds, how will that effect closer shots, like 50 or 75 yard shots?
C/O is offline  
Old December 25, 2012, 09:41 PM   #8
Doyle
Senior Member
 
Join Date: June 20, 2007
Location: Rainbow City, Alabama
Posts: 7,167
What model Bushnell? They come in various models from super cheap Walmart specials (that aren't likely to hold zero) to high-end models that are very well made.
Doyle is offline  
Old December 25, 2012, 09:42 PM   #9
C/O
Senior Member
 
Join Date: December 8, 2004
Posts: 232
The box says Trophy XLT, but the sticker on the scope says DOA 600.
733960B

It came from Dick's sporting goods.
C/O is offline  
Old December 25, 2012, 09:56 PM   #10
Doyle
Senior Member
 
Join Date: June 20, 2007
Location: Rainbow City, Alabama
Posts: 7,167
Their Trophy line is the lowest of their line that I would ever own (in fact, I do own one or two). It should do OK for you. For it changing POI as you zoom, yes it will likely change some but not enough to really worry about. That Marlin 30-30 is probably only going to give you 2-3 MOA accuracy at best anyway so the small shift in POI won't be noticed. I would sight it in at a medium setting. That way, any change would be pretty much limited to the extreme high and low magnifications.
Doyle is offline  
Old December 26, 2012, 03:25 AM   #11
MarkDozier
Senior Member
 
Join Date: February 1, 2010
Posts: 363
2 or 3 MOA is roughly 1/2 to 3/4 inch.
this link may help you understand answers to your question. It is a rather fasinating subject.

By the 3x9x40 is about the most common on the 30-30 Marlin.
MarkDozier is offline  
Old December 26, 2012, 03:34 AM   #12
tahunua001
Senior Member
 
Join Date: July 21, 2011
Location: Idaho
Posts: 7,839
normally with quality glass the point of impact wont change but it may be harder to tell if you are not holding steady on 3 power than it is on 9 power so your accuracy free hand will probably slip to some degree but the scope will still be zeroed.
__________________
ignore my complete lack of capitalization. I still have no problem correcting your grammar.
I never said half the stuff people said I did-Albert Einstein
You can't believe everything you read on the internet-Benjamin Franklin
tahunua001 is offline  
Old December 26, 2012, 07:55 AM   #13
Mobuck
Junior member
 
Join Date: February 2, 2010
Posts: 6,846
Considering the effective range of the 30/30, you have a lot of stuff in your scope that you can't use/don't need. Just sight it in a little high at 100 yards and hold on the brown to 200. Beyond that, you need more gun. All those aiming points for longer range are irrelevant.
Mobuck is offline  
Old December 26, 2012, 08:01 AM   #14
jmr40
Senior Member
 
Join Date: June 15, 2008
Location: Georgia
Posts: 10,792
Your new Bushnell is at best a small step up in quality over the Tasco.

I've never noted enough difference in POI at differing scope powers for it to be a real issue. I use the scopes highest power setting when zeroing at 100 yards. Then I run it down to the lowest power setting and shoot at some targets at closer ranges to verify the zero.

I leave the scope on the lowest setting for anything inside of 50 yards and use the highest magnification for every thing else. I have no use for anything in between. This way for longer shots I know the scope is zeroed correctly. If there is any difference on another power setting it won't be enough to matter at closer ranges.

I know lots of guys who use 3-9's on 30-30's, but I think it is way too much scope for the gun. They are just too big and hurt the guns balance. At 3X you have almost too much magnification for really close fast shots and you will never need 9x at 30-30 ranges. I would prefer a 1-4X20 on a 30-30 and no more than a 2-7X32. If returning the scope and replaceing it is an option I would. If not, then mount it as low as possible and use it. It isn't ideal in my opinion, but certainly useable.

This is what I'd prefer on a 30-30

http://swfa.com/Leupold-1-4x20-VX-1-...pe-P51851.aspx

At 8 oz it is about 1/2 the weight of most 3-9's and more than adequate.
jmr40 is offline  
Old December 26, 2012, 11:20 AM   #15
C/O
Senior Member
 
Join Date: December 8, 2004
Posts: 232
Thanks for all the replies.
C/O is offline  
Old December 26, 2012, 12:26 PM   #16
Tom Matiska
Senior Member
 
Join Date: April 12, 2000
Location: Wilkes-Barre, Pa
Posts: 1,029
Pages 6 to 8 of your scope manual says sight in at any mag, but use 9x for range lines to work. Your Marlin with FTX loads is a legit 250 yard rifle, and only a few inches worse than 150gr/3006 loads those lines are intended for(out to 300). I'd bet a beer if you sight in about 1.5 or 2 inches high at 100 the 200 and 300 lines will within an inch or two.
Tom Matiska is offline  
Old December 26, 2012, 12:40 PM   #17
SSA
Senior Member
 
Join Date: August 1, 2010
Posts: 641
With standard 30/30 ammo, if you zero at 100 yards, the first two holdover points (at 9X) might line up at just about 150 and 200. You'd have to shoot it to know for sure.
Sighted in at 100, you'd be within an inch high or low at any range from about 15 yards to 125. At any magnification.
SSA is offline  
Old December 26, 2012, 01:48 PM   #18
Erno86
Senior Member
 
Join Date: September 22, 2012
Location: Marriottsville, Maryland
Posts: 1,738
[QUOTE]"First focal plane 'European' scopes cannot change point of impact when changing magnification because the reticle does not move.
First plane scopes with rangefinding type reticles may be used at any power.

Second focal plane scopes or 'American' scopes are smaller and lighter and can have point of impact change magnification, and many of them, especially less expensive one's certainly do. Second plane scopes with rangefinding type reticles are designed to be used at one power only. Second plane scopes also have a smaller appearing reticle on the target at high power than low power, which is extremely important for precise shot placement."[QUOTE]
Erno86 is offline  
Old December 26, 2012, 04:46 PM   #19
Doyle
Senior Member
 
Join Date: June 20, 2007
Location: Rainbow City, Alabama
Posts: 7,167
Quote:
2 or 3 MOA is roughly 1/2 to 3/4 inch.
No, 2 or 3 MOA is roughly 2 to 3 inches at 100 yds.
Doyle is offline  
Old December 26, 2012, 05:18 PM   #20
Picher
Senior Member
 
Join Date: December 14, 2004
Location: Maine
Posts: 3,694
I like the 3-9X magnification for deer hunting, especially if you must spot antlers. Sometimes it's hard to see antlers in the woods in low light, so even if you normally leave the scope on 4X and identify a deer, but need more power to see antlers, it's quicker to do so with the scope than switching to binoculars.

(That said, someone will say it's not safe to use a scope to spot deer, but I'm saying that you've already spotted the deer, just need to identify it's an antlered deer.)

On the other side, the 9x power makes sighting-in easier and somewhat more accurate to sight-in the rifle.

Yes, 3-9X scopes are a bit big and heavy for .30-30s, but your dad got it for you and it's entirely usable. Besides, some day you may want to buy a bolt-action rifle in a more powerful cartridge, like a .270 or .30-06, which would extend your in-zero range.
Picher is offline  
Old December 26, 2012, 05:41 PM   #21
Art Eatman
Staff in Memoriam
 
Join Date: November 13, 1998
Location: Terlingua, TX; Thomasville, GA
Posts: 24,798
Whether necessary or not, I'll happily put a 3x9x40 on most anything. 3X when hunting, particularly when sneaky-snaking and walking. 9X when messing around on paper, load testing or sighting in.

"If ya got it, use it."
Art Eatman is offline  
Old December 26, 2012, 06:28 PM   #22
C/O
Senior Member
 
Join Date: December 8, 2004
Posts: 232
Quote:
Originally Posted by Picher View Post
I like the 3-9X magnification for deer hunting, especially if you must spot antlers. Sometimes it's hard to see antlers in the woods in low light, so even if you normally leave the scope on 4X and identify a deer, but need more power to see antlers, it's quicker to do so with the scope than switching to binoculars.

(That said, someone will say it's not safe to use a scope to spot deer, but I'm saying that you've already spotted the deer, just need to identify it's an antlered deer.)

On the other side, the 9x power makes sighting-in easier and somewhat more accurate to sight-in the rifle.

Yes, 3-9X scopes are a bit big and heavy for .30-30s, but your dad got it for you and it's entirely usable. Besides, some day you may want to buy a bolt-action rifle in a more powerful cartridge, like a .270 or .30-06, which would extend your in-zero range.






Quote:
Originally Posted by Art Eatman View Post
Whether necessary or not, I'll happily put a 3x9x40 on most anything. 3X when hunting, particularly when sneaky-snaking and walking. 9X when messing around on paper, load testing or sighting in.

"If ya got it, use it."
Thanks, I think I will keep it and use it.
C/O is offline  
Old December 26, 2012, 07:05 PM   #23
FALPhil
Senior Member
 
Join Date: September 10, 2007
Location: Racoon City
Posts: 934
Quote:
jmr40 wrote:
Your new Bushnell is at best a small step up in quality over the Tasco.
jmr, what do you base this statement on? I have to assume it is merely your opinion since you did not back it up.
FALPhil is offline  
Old December 26, 2012, 07:37 PM   #24
reynolds357
Senior Member
 
Join Date: December 10, 2012
Posts: 6,161
Zero should not move when changing power.
reynolds357 is offline  
Old December 26, 2012, 07:40 PM   #25
reynolds357
Senior Member
 
Join Date: December 10, 2012
Posts: 6,161
Bushnell may or may not be a step up over Tasco. Bushnell makes the "banner," the "elite 6500," and a lot in between. Tasco makes some terrible stuff and at times they have turned out some pretty good stuff. I have a Tasco custom shop scope that is as good as my Leupold bench rest scope that was manufactured during the same time period. I also had a scope come from the Tasco custom shop with oil all over the inside of the lenses.
reynolds357 is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:35 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.09166 seconds with 10 queries