|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
August 8, 2012, 05:32 PM | #1 |
Senior Member
Join Date: May 25, 2011
Posts: 1,755
|
Powder Sticking to the Hopper, Remedies?
I have a lee auto disk pro. The other day when I emptied the hopper back into the bottle, powder was stuck to the sides. I would imagine this is due to a small amount of static build up, on the plastic surface. What are some tips or tricks to getting it not to stick?
|
August 8, 2012, 05:37 PM | #2 |
Senior Member
Join Date: June 16, 2011
Location: Ohio
Posts: 1,497
|
Same thing going on myself - bit o' powder clinging to the sides of the hopper. I figured it was from humidity as we had a couple of rather steamy days. I left it be.
__________________
"The best diplomat I know is a fully charged phaser bank" - Montgomery Scott |
August 8, 2012, 05:46 PM | #3 |
Senior Member
Join Date: May 25, 2011
Posts: 1,755
|
I would guess that too, but I live in the desert.
|
August 8, 2012, 05:49 PM | #4 |
Senior Member
Join Date: August 18, 2009
Posts: 826
|
The hopper is plastic, yes ? If so, then the cause is likely static electricity.
I've always addressed this, on my plastic reloading tools, by rubbing down the area in question with some gun powder, so as to sort of "dirty up" the plastic. This leaves a fine coating of dust-like powder residue, which seems to almost eliminate sticking of powder granules. At any rate, it works for me. |
August 8, 2012, 06:47 PM | #5 |
Senior Member
Join Date: March 21, 2006
Location: marlow okla
Posts: 227
|
i use the same thing i put in the dryer to take static from clothes, just wrap in on outside. cjs
|
August 8, 2012, 07:10 PM | #6 |
Senior Member
Join Date: May 29, 2011
Location: Fort Worth
Posts: 500
|
I rolled up a new dryer sheet and keep it in my hopper when I am not using it. -0- static cling.
Be sure to remove it before you pour the powder into the hopper. Would be kind of messy getting it out.
__________________
Education teaches you the rules, experience teaches you the exceptions (Plagiarized from Claude Clay) |
August 8, 2012, 07:12 PM | #7 |
Senior Member
Join Date: August 10, 2000
Location: WI
Posts: 1,395
|
Wipe it down with powdered graphite.
__________________
A plan is just a list of things that doesn't happen. |
August 8, 2012, 08:30 PM | #8 |
Senior Member
Join Date: May 25, 2011
Posts: 1,755
|
I'll have to try the dryer sheet thing. Thanks for the info!
|
August 9, 2012, 12:29 AM | #9 |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,424
|
Once you start building up some graphite in the hopper, don't wipe the inside with a dryer sheet. It just sets you back, again. Let the graphite build up inside, but wipe the outside with a dryer sheet, occasionally.
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
August 9, 2012, 12:44 AM | #10 |
Senior Member
Join Date: May 25, 2011
Posts: 1,755
|
Noted, so far the hopper has only been loaded once, and I wiped it out with a paper towel to remove stuck powder. But after trying the dryer sheet before next time, I will avoid wiping it out.
|
August 9, 2012, 03:16 PM | #11 |
Member
Join Date: December 5, 2011
Location: Southern California
Posts: 74
|
I went through the same thing with my uniflow powder measurer and I did the dryer cloth remedy and it worked. I then ran about a pound of powder though it and I still get a little powder sticking but no where near as bad as when it was new.
|
August 9, 2012, 10:59 PM | #12 |
Member
Join Date: October 23, 2011
Posts: 75
|
I had the same problem when I started using my RCBS powder measure, but after using it some, it kind of broke in and the static disappeared. The graphite in the powder builds up in the measure, and things get much better.
|
|
|