The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools Search this Thread
Old September 26, 2010, 08:49 AM   #1
skinsman
Member
 
Join Date: April 20, 2010
Posts: 75
Cap size question

This forum has been good to me for a new BP shooter, I shot for the first time, and it was a blast. I had one issue, after about 4 shots the last 2 caps seems to have wiggled loose. Is this normal? Or even though the caps seem to fit good maybe I have one size to large? Thanks.
skinsman is offline  
Old September 26, 2010, 11:36 AM   #2
GNLaFrance
Member
 
Join Date: June 29, 2008
Location: Near Baltimore, the Soviet Socialist Democratic People's Republic of Maryland
Posts: 81
You must be shooting a revolver, right? What is the make and model? Bought new or used?

The two common sizes of cap are #10 and #11. #10 caps are slightly smaller than #11 caps. If you're using #11, get some #10 and see if they fit better. They should fit snugly, that is, you should have to press a bit to get it all the way down on the cone of the nipple. WARNING: Do NOT push the cap onto the nipple with your finger or thumb. If the cap sparks from the pressure, the powder in the charge hole will make an ugly mess of your finger or thumb, not to mention send the ball out the side of the frame. Get a good quality capper or use something like a Popsicle stick.

If the caps split when you press them down, then the nipples are too big. Take them out, chuck them into a drill and slowly and carefully sand or file them down, checking frequently, until the caps fit snugly.

Besides being a pain in the butt, a cap falling off means the nipple is open and when the cap under the hammer fires, it could send a spark into the other nipple and set off the charge; this is called a "chain fire". It's usually not harmful to the gun, but it is scary and can be dangerous.
__________________
Guy N. LaFrance
Collector of Curios & Relics, Maryland Designated Collector
Maryland Shall Issue, GOA, NRA, SAF, JPFO
Grand Army of the Frontier, National Congress of Old West Shootists
GNLaFrance is offline  
Old September 26, 2010, 12:20 PM   #3
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
If you're using #11 caps you can go to #10. If you're already using #10 you can try different brands. You can also pinch them together slightly before you put them on. Caps are impact sensitive, not pressure sensitive and wont go off from finger seating.
Hawg is offline  
Old September 26, 2010, 03:18 PM   #4
Rifleman1776
Senior Member
 
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
HH said it. Caps sizes do vary brand to brand.
Rifleman1776 is offline  
Old September 26, 2010, 03:30 PM   #5
mykeal
Senior Member
 
Join Date: October 8, 2006
Location: Northern Michigan
Posts: 2,772
Sorry, Hawg, but if he's using Remington No. 11's, going to Remington No. 10's doesn't mean he'll be getting a smaller cap. It MAY (or may not) fit further down the cone, and thus appear to be a better fit, but it's not smaller.

Cap size numbers are utterly and totally meaningless. Once again, here's the data, measured from at least 20 samples of each brand and 'size':

Remington No. 10's are not the same size as CCI No. 10's, nor are the No. 11's the same size. Furthermore, Remington No. 11's are actually smaller than Remington No. 10's.

To make things even more interesting, there's absolutely no standardization in the size of the nipple cone that the cap fits on.

Finding the right size cap is essentially a crap shoot. You can dress the nipple cone to fit whatever brand and size of caps you happen to have on hand, but you don't get 3 decimal place precision for 4 cents in today's world, so good luck on the next batch being the same size.
mykeal is offline  
Old September 26, 2010, 04:12 PM   #6
GNLaFrance
Member
 
Join Date: June 29, 2008
Location: Near Baltimore, the Soviet Socialist Democratic People's Republic of Maryland
Posts: 81
Quote:
Originally Posted by Hawg Haggen
Caps are impact sensitive, not pressure sensitive and wont go off from finger seating.
One of the pards on CAS City, "Cuts Crooked", set off a cap with thumb pressure. Here's the thread where Cuts tells his story and shows a pic of his injury.

http://www.cascity.com/forumhall/ind...ic,1620.0.html
__________________
Guy N. LaFrance
Collector of Curios & Relics, Maryland Designated Collector
Maryland Shall Issue, GOA, NRA, SAF, JPFO
Grand Army of the Frontier, National Congress of Old West Shootists
GNLaFrance is offline  
Old September 26, 2010, 05:44 PM   #7
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
Yeah but i'm betting there's more to it than he's telling. I've personally taken a wooden dowel and put all the pressure I could on one and couldn't make it go off.
Hawg is offline  
Old September 27, 2010, 04:14 PM   #8
GNLaFrance
Member
 
Join Date: June 29, 2008
Location: Near Baltimore, the Soviet Socialist Democratic People's Republic of Maryland
Posts: 81
Quote:
Originally Posted by Hawg Haggen
Yeah but i'm betting there's more to it than he's telling. I've personally taken a wooden dowel and put all the pressure I could on one and couldn't make it go off.
I'm looking forward to you showing up on CAS City to present your opinion and argue your case.
__________________
Guy N. LaFrance
Collector of Curios & Relics, Maryland Designated Collector
Maryland Shall Issue, GOA, NRA, SAF, JPFO
Grand Army of the Frontier, National Congress of Old West Shootists
GNLaFrance is offline  
Old September 27, 2010, 06:52 PM   #9
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
Quote:
I'm looking forward to you showing up on CAS City to present your opinion and argue your case.
Why? Would just be my word against his.
Hawg is offline  
Old September 27, 2010, 08:47 PM   #10
mykeal
Senior Member
 
Join Date: October 8, 2006
Location: Northern Michigan
Posts: 2,772
This has been 'discussed' on other forums (besides the vaunted CAS City); Mr. Cuts Crooked is the only person to ever make this claim that I've seen. Hawg is absolutely correct about the chemical nature of the material used in percussion caps - it's only impact sensitive, which means the force time history must have at least one sharp edge.

I'm not saying one should not use caution; that's prudent any time you're working with explosives, but I don't believe carefully applied thumb pressure has any likelihood of igniting a percussion cap. You can believe whatever you want.

And no, I'm not going to go to CAS City and start an argument - I don't really care one way or the other what the members of that forum believe on this subject.
mykeal is offline  
Old September 27, 2010, 09:25 PM   #11
GNLaFrance
Member
 
Join Date: June 29, 2008
Location: Near Baltimore, the Soviet Socialist Democratic People's Republic of Maryland
Posts: 81
In that case, I hope you two won't be upset if I continue to believe the story as told by Cuts Crooked. After all, he was there and we weren't.
__________________
Guy N. LaFrance
Collector of Curios & Relics, Maryland Designated Collector
Maryland Shall Issue, GOA, NRA, SAF, JPFO
Grand Army of the Frontier, National Congress of Old West Shootists
GNLaFrance is offline  
Old September 27, 2010, 09:26 PM   #12
denster
Senior Member
 
Join Date: April 24, 2010
Location: Ohio
Posts: 581
I'm inclined to agree with Hawg and Mykeal. I've used far more force with the haqmmer or a push stick than anyone could ever exert with a thumb and have never set off a cap.
denster is offline  
Old September 27, 2010, 09:31 PM   #13
shortwave
Senior Member
 
Join Date: December 17, 2007
Location: SOUTHEAST, OHIO
Posts: 5,970
As Hawgs suggested, want your cap to fit a bit more snug, squeeze the opened end of cap a bit till you get your desired fit.

Also, I'm not a believer of normal thumb capping pressure igniting caps.
Just don't hammer the cap on .
shortwave is offline  
Old September 29, 2010, 07:22 AM   #14
Roaddog
Senior Member
 
Join Date: July 16, 2010
Location: East central Minnesota
Posts: 202
The cap should be # 10 for a revolver and should fit tight to avoid chain fire. That said, I know there is a difference in cap brands. I would stick to #10 and check the different ones before going to #11.
Roaddog is offline  
Old September 29, 2010, 05:46 PM   #15
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
Quote:
The cap should be # 10 for a revolver and should fit tight to avoid chain fire.
Most do take 10's. I've had a few that took 11's and have one that takes 9's.
Hawg is offline  
Old September 29, 2010, 06:45 PM   #16
rosewood
Member
 
Join Date: March 30, 2010
Location: conn
Posts: 19
I had trouble getting caps to fit my dragoon so i picked up some ampco nipples, now my #10 caps are a perfect fit. I assume those of you who squeeze your caps are not using a capper, is this so? Also someone had mentioned chucking a nipple in a drill and using a file on it, how do you prevent stripping the threads?
rosewood is offline  
Old September 29, 2010, 09:27 PM   #17
mykeal
Senior Member
 
Join Date: October 8, 2006
Location: Northern Michigan
Posts: 2,772
You don't attach the chuck to the threads; you attach it to the larger diameter just above the threads. You run the drill slowly and don't use a lot of force on the file.
mykeal is offline  
Old September 30, 2010, 09:12 AM   #18
Noz
Senior Member
 
Join Date: February 25, 2009
Posts: 643
Rose wood, I chuck the threads into the drill with out using a chuck key, hand tight. I run the drill at low speed and lightly touch the file. I have not damaged the threads on any nipple yet.

Pinching caps is a useless operation. Get nipples that fit.
Noz is offline  
Old September 30, 2010, 12:27 PM   #19
arcticap
Senior Member
 
Join Date: March 15, 2005
Location: Central Connecticut
Posts: 3,166
Quote:
Originally Posted by rosewood
Also someone had mentioned chucking a nipple in a drill and using a file on it, how do you prevent stripping the threads?
I didn't use a drill and just carefully dressed the nipple by hand.
arcticap is offline  
Old September 30, 2010, 02:43 PM   #20
andrewstorm
Junior member
 
Join Date: October 4, 2009
Posts: 198
loose caps

I had the same problem,thumb pressure,and the correct cap,for my r.o.a.s that is cci 11 mag,pushed hard with thumb,while pointed in a safe direction,once you find the correct cap,and everything is clean,you shouldnt have any more problems,
andrewstorm is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:10 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.37297 seconds with 10 queries