March 11, 2001, 12:04 AM | #1 |
Junior member
Join Date: January 6, 2000
Location: AZ
Posts: 1,236
|
I am loading up a batch of 200gr RNFPs for my 1894 Marlin carbine, I am leaning towards Unique for my powder.
I am not looking for hot loads the slugs are hard cast but probably won't tolerate much over 1200fps. If putting recipes on the net is a problem, then point me in the right direction and I will follow up. Any info welcome Waterdog |
March 11, 2001, 01:04 AM | #2 |
Senior Member
Join Date: April 2, 1999
Location: U.S.A.
Posts: 566
|
|
March 11, 2001, 10:36 PM | #3 |
Senior Member
Join Date: May 19, 2000
Posts: 176
|
Try 10.0 grains of Unique. I've used this load for years in my pistol behind a 215 grain cast bullet.
TS |
March 12, 2001, 09:32 PM | #4 |
Senior Member
Join Date: October 13, 1998
Location: Chandler, Az, USA
Posts: 125
|
Weird as it sounds if you go to a slightly "softer" bullet in the .44 Mag you can get higher velocities and less "leading". It has to do with the time at which the bullet obulates (sp.) (seals barrels from the hot gases pusing it). The hard cast takes a fraction of a sec. longer and allows hot, cutting gases to get past and cause leading from side of bullet.
I can drive a lead bullet in my 444 marlin at over 2000fps with very little leading (even in a micro groove barrel!). |
March 15, 2001, 10:27 PM | #5 |
Junior member
Join Date: January 6, 2000
Location: AZ
Posts: 1,236
|
Wolfz, are your slugs gas checked?
Waterdog |
March 18, 2001, 10:36 AM | #6 |
Senior Member
Join Date: October 13, 1998
Location: Chandler, Az, USA
Posts: 125
|
Yes they are gas checked. But I'm driving them real hard!
|
March 20, 2001, 03:40 AM | #7 |
Senior Member
Join Date: October 9, 1998
Location: Ohio USA
Posts: 8,563
|
My "plinking" load for the .44mag is 15.8 to 17.3 grains of 2400 under a 240 grain lead SWC hollow point. YMMV as to your success with a SWC bullet in your lever action though. Seating depth and amount of crimp was largly a matter of trial and error for me. I use this load in a Winchester Trapper with good results. I guestimate around 1000 fps out of this load, which is plenty fast enough for me and 25 or 50 yard paper targets. The 2400 gives better shot to shot consistancy, doesn't lead the barrel, is bulkier in the case and therefore easier to "eyeball" for an overcharge, has more of a "boom" rather than a "crack", and seems a bit easier on the shoulder over the same velocity loads using Unique. I'm personally partial to 240 grain over the lighter 200 to 215 grain slugs, but YYMV. I owrked this load up about a year ago. I wanted something between the Cowboy loads, and the standard loads listed at Alliant.com.
The bullet I use mostly is the Hornady stock # 11118, a swaged(or so I'm told) lead 44 cal .430 240 gr SWC/HP. They're a bit more than the gun show special cast lead bullets, but I like the dry powder lube Hornady uses, and I have yet to have to size one. I measured an entire box of 400, and each one was spot on at .430. |
March 22, 2001, 12:01 AM | #8 |
Guest
Posts: n/a
|
Waterdog, I've been using the combination you've described in my Marlin 1895S with excellent results. No problems with barrel leading, and despite what I've heard about Unique being dirty with cast bullets, I've got no complaints. 10.0 grains feels about right, although I've downloaded to 7.0 grains just to experiment. My Marlin feeds the D&J cast 200-grn. RNFP's well, haven't had a misfeed yet.
Shoot straight, freedomlover |
March 22, 2001, 06:49 PM | #9 |
Senior Member
Join Date: March 10, 2001
Posts: 402
|
Unique is my fvorite powder in the big revolvers. I load as light as 7 grains, but you can go higher. As someone earlier had advised, check with Alliant. I have a Winchester 94 in 44 mag and it never ceases to amaze me as to how hard that thing can kick.
|
|
|