October 14, 2012, 05:21 AM | #1 |
Senior Member
Join Date: November 27, 2005
Posts: 1,419
|
Clean BP brass
Is there any way to clean brass that has black powder fouling in it without a tumbler?
Shot some black in my.45-70 yesterday ( I never had so much fun shooting a rifle! ) and now I can't get the brass clean. Right after shooting them I dropped the empty brass in a milk carton with warm water and dish washer and let em soak for a couple of hours, then I put them into my washing machine (in a bag) with some dirty laundry. Now they still look like dirty little chimneys. I tried to clean them mechanically with a 45 caliber bronze brush attached to a drill but that didn't work that great. Help! Its a race against time because they are already starting to corrode inside. Why I don't have a tumbler? I never needed one, the washing machine took care of dirty nitro fouled brass! |
October 14, 2012, 07:05 AM | #2 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
|
You can probably get it out with Windex with vinegar or just vinegar and water and a 410 bore mop.
|
October 14, 2012, 04:33 PM | #3 |
Senior Member
Join Date: November 27, 2005
Posts: 1,419
|
Tried it with apple vinegar, let em soak a couple of minutes than ran a brush through them and cleaned them with hot water. Didn't work at all.
Could I simply boil the brass in hot water? |
October 14, 2012, 05:03 PM | #4 |
Senior Member
Join Date: November 23, 2000
Location: England
Posts: 455
|
I use a very strong detergent, such as they use to clean printed circuit boards with (don't put your hand in it)
|
October 14, 2012, 05:47 PM | #5 |
Senior Member
Join Date: November 27, 2005
Posts: 1,419
|
Aside from a few rust removers I don't have any strong detergents. I let my brass soak in a vinegar-salt mix and now I put the cases in boiling water - it works, not very well but its better than letting the brass stay dirty and rot away.
|
October 14, 2012, 06:10 PM | #6 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
|
I don't soak mine immediately after firing and it always has black stains but no corrosion. I do tumble it tho.
|
October 15, 2012, 10:21 AM | #7 |
Senior Member
Join Date: November 25, 2010
Location: Cody, Wyoming
Posts: 111
|
You're not going to make them shiny again without a tumbler but the staining is nothing more than an eye sore.
I throw mine into a bowl with Dawn dishwashing soap to soak then use a baby bottle nipple brush to just swab the insides. Rinse with hot water then let 'em dry real good. I did very well without a tumbler for quite a while but eventually did buy a Frankfort Arsenal cheapy and 40lb of blasting media to keep it fed. I've found that tumbled brass that has had NuFinish added to the media helps in carbide dies, especially the 9mm that takes a little umph to de-prime and size.
__________________
Foto Joe |
October 15, 2012, 10:49 AM | #8 |
Senior Member
Join Date: February 25, 2009
Posts: 643
|
If you are going to shoot black and want shiny cases, bite the bullet and get a tumbler. Wet tumbling with ceramic or steel is the best way to go.
I haunted e-bay for about 6 months before I found a Thumler the no one else saw. Got her cheap. |
October 15, 2012, 04:59 PM | #9 |
Senior Member
Join Date: January 29, 2005
Location: Southern California
Posts: 344
|
I ruined a Lyman vibrator tumbler and replaced it with a Harbor Freight version. It was far cheaper, and so has lasted far longer.
For media, I get the cheap reptile bedding at the pet store. I believe it is called Lizard Litter. It's almost the same thing as brand name crushed walnut, maybe a little coarser. I have friends who paid quality money for Thumbler rotary tumblers and are having great success with stainless steel pins!! Photos I've seen look like new brass. Too pricy for me though. |
October 17, 2012, 10:49 AM | #10 |
Senior Member
Join Date: June 6, 2004
Location: Rocky Mts
Posts: 859
|
When I shot black in 45-70 and 44 spl, I'd drop the cases in a pot of water and simmer them gently on the stove, then lay on a towel to dry, then load. They had a dark stain, but as was already mentioned, it doesn't hurt anything. I still have some of those cases in my pile, though I had a freind run them through his tumbler after I quit shooting black. It didn't get all the stain off. Doesnt bother me, I ignore the stain.
__________________
"Far better it is to dare mighty things, to win glorious triumphs even though checkered by failure, than to rank with those poor spirits who neither enjoy nor suffer much because they live in the gray twilight that knows neither victory nor defeat." -Theodore Roosevelt- |
October 17, 2012, 12:04 PM | #11 | ||
Senior Member
Join Date: June 17, 2010
Location: Virginia
Posts: 6,869
|
Quote:
LL/walnut works perfectly/beautifully to turn thoroughly-BP stained/"bronzed" cases back to absolutely pristine/shiny brass overnight in a vibratory cleaner. Quote:
vibratory cleaner and "switch-on" is the comparative cat's meow. |
||
October 17, 2012, 09:59 PM | #12 |
Senior Member
Join Date: October 14, 2009
Location: San Diego County
Posts: 795
|
If you want them really clean you have to tumble.
I soak mine in a mild dish soap mixture on the way home, then rinse in hot water and tumble.
__________________
US Navy Retired,NRA Life Member,SASS member, Time magazine's Person of the Year 2006! |
Thread Tools | Search this Thread |
|
|