The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old June 26, 2010, 08:30 AM   #1
carolinadrifter
Junior Member
 
Join Date: January 22, 2006
Location: NW SC
Posts: 14
Noobie Revolver Question

Is the ring wear on the cylinder just a fact of life or can it be lessoned?

Thanks
__________________
Forgive me Lord Jesus for having meaness in my heart for I am a Warrior and I will never forget.

NRA DLM, AFM, Disabled Veteran, SCCWP
carolinadrifter is offline  
Old June 26, 2010, 02:15 PM   #2
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,678
If you're referring to a wear line around the outside of the cylinder between the indexing notches, it is an indication that the revolver is out of time and raising the stop latch too early, letting it drag on the cylinder outer surface ILO into the notch's leade.

A revolversmith should be able to remedy the timing, but only a cylinder refinish will remove the evidence.

.
PetahW is offline  
Old June 27, 2010, 12:01 AM   #3
RJay
Senior Member
 
Join Date: November 2, 2005
Location: Arizona
Posts: 1,936
All that is true, but I've yet to see a well used blued revolver with out the ring marks. Regardless of make.
RJay is offline  
Old June 27, 2010, 12:21 AM   #4
vytoland
Senior Member
 
Join Date: August 23, 2008
Location: Illinois
Posts: 614
all my SS S&W revolvers have "ring around the cylinder", all are in time and all are very accurate, when i do my part.
vytoland is offline  
Old June 27, 2010, 01:16 AM   #5
ogree
Senior Member
 
Join Date: January 18, 2005
Location: Idaho
Posts: 151
It is something a good revolver smith can cure but you will have to spend the money.
It is just a fact that this occurs on almost all revolvers and has no detriment on the life of the gun.
ogree is offline  
Old June 27, 2010, 04:58 PM   #6
TXGunNut
Senior Member
 
Join Date: January 16, 2010
Location: If you have to ask...
Posts: 2,860
Haven't seen a S&W revolver yet that didn't get a light ring from the cylinder stop after a few dozen rounds. Too much pressure on the stop can cause excessive wear on the stop and cylinder but light pressure is normal.
__________________
Life Member NRA, TSRA
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call Lonesome Dove
My favorite recipes start out with a handful of used wheelweights.
TXGunNut is offline  
Old June 27, 2010, 05:09 PM   #7
Rifleman1776
Senior Member
 
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
Not doubting Petewh but I have never seen a used revolver that didn't have the 'ring'.
Rifleman1776 is offline  
Old June 27, 2010, 06:39 PM   #8
Dfariswheel
Senior Member
 
Join Date: May 4, 2001
Posts: 7,476
Virtually all modern double action revolvers will quickly develop the ring.

This is due to the fact that the cylinder locking bolt is specifically designed to actually "ride" on the cylinder for most of it's rotation.
When metal rubs metal, you get a wear mark.
Slowly cock a modern revolver, as the hammer comes back, you'll hear a distinct "click". That's the cylinder locking bolt dropping back onto the cylinder. The bolt will ride on the cylinder for most of it's rotation.

You can also see this process. Hold a revolver up to the light and look between the bottom of the cylinder and the frame "window" as you cock the hammer.
You'll see the cylinder locking bolt retract, the cylinder start to turn and the locking bolt dropping back onto the cylinder. The bolt will maintain contact with the cylinder as it turns.

The only modern DA revolver that doesn't necessarily get the wear mark is the old Colt action like the Python and Detective Special.
These are designed so the bolt doesn't ride the cylinder.
However, from opening and closing the cylinder and normal use, these too will get the wear mark.

In short, the wear ring on a revolver is a feature of the design and is entirely normal.

Last edited by Dfariswheel; June 27, 2010 at 06:45 PM.
Dfariswheel is offline  
Old June 27, 2010, 07:42 PM   #9
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,678
[The only modern DA revolver that doesn't necessarily get the wear mark is the old Colt action like the Python and Detective Special.]

Well, although my 1966 DS is certainly sans ring, FWIW so is my 1970's Charter Arms snubbie, & a 2y.o. Charter Pathfinder - none of which are safe queens.

.
PetahW is offline  
Old June 27, 2010, 09:52 PM   #10
BruceM
Senior Member
 
Join Date: March 12, 2006
Location: SE Wisconsin
Posts: 285
"If you're referring to a wear line around the outside of the cylinder between the indexing notches, it is an indication that the revolver is out of time and raising the stop latch too early, letting it drag on the cylinder outer surface ILO into the notch's leade."

On Smith & Wesson DA revolvers, that is a sign of normal operation of the action. It absolutely is NOT a timing defect. Anybody from Smith & Wesson will verify this including the smiths in their Performance Center. That said, there are ways to minimized but not eliminate that type of wear. On revolvers of different manufacture, the story is different.



Bruce
BruceM is offline  
Old June 28, 2010, 07:32 PM   #11
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
On S&W revolvers, that ring is a fact of life; don't worry about it.

Some revolvers, like the Colt SAA and the old Colt DA's can be timed to drop the cylinder bolt (stop) in the leade (that triangular shaped cut ahead of the stop notch). One reason is that the spring on the bolt on both the SAA and the DA's is very strong and will mar the cylinder if the bolt drops too soon. As a practical matter, that doesn't make any difference, but some users get so worked up that a timing job on those guns usually involves both modifying the drop point and reducing the bolt spring tension.

On most other revolvers (except Colt SAA clones), there is no problem except a purely cosmetic one.

Jim
James K is offline  
Old June 28, 2010, 07:46 PM   #12
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,175
One thing about single actions, if you let the hammer down from half cock it will ring the cylinder. Always bring it to full cock before lowering it.
Hawg is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.04908 seconds with 10 queries