August 20, 2009, 11:01 PM | #76 | |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,188
|
Quote:
But a vice can do jobs a hammer often can't. Or do them neater and with less damage. |
|
August 20, 2009, 11:22 PM | #77 |
Senior Member
Join Date: December 4, 2005
Location: Mojave Desert, CA
Posts: 1,195
|
ClemBert where exactly is the end of the wedge at this point in relation to the barrel slot?
can you depress or dremel away the wedge catch(lip) that is spring loaded? Just a thought that the spring lip is caught up on the inside of the barrel frame or on the outside..
__________________
"I Smoke Black Powder" "Favor an 1858 Remington" SGT. Smokin' Gun, Mosby's Rangers 43rd Virginia Cavalry C.S.A. SASS# 19634, ... Admin:http://blackpowdersmoke.com/oldcoots/index.php |
August 20, 2009, 11:30 PM | #78 |
Senior Member
Join Date: March 2, 2009
Location: Orlando
Posts: 936
|
The wedge is basically flush with the barrel or I should say just barely protruding. This is the case with both of those 1851's they sent me. Just about identical. The catch is barely sticking out as you point out. I wouldn't doubt if the problem is what you pointed out. I think I should just shoot the hell outta that bad boy then come home and attempt to tap it out. If it still is a beast then probably a dremel tool or blasting caps are in order.
|
August 20, 2009, 11:56 PM | #79 |
Senior Member
Join Date: December 4, 2005
Location: Mojave Desert, CA
Posts: 1,195
|
Hell at this point I think I would too...jus' try takin' the wedge out a cylinder full at a time.
Is yours an 1851 Lawman .44 white grips and engraved some?? I have forgotten. One other thing I had thought about was ...if the wedge screw on the bbl fits up good against the wedge I've used thethat screw to help remove a wedge when i had no mallet...put a lil tension on the screw as to attempt forcing the wedge out and tap or smack it hard with a dead blow hammer...and keep tension on the wedge with the screw. Just a thought.
__________________
"I Smoke Black Powder" "Favor an 1858 Remington" SGT. Smokin' Gun, Mosby's Rangers 43rd Virginia Cavalry C.S.A. SASS# 19634, ... Admin:http://blackpowdersmoke.com/oldcoots/index.php |
August 21, 2009, 12:00 AM | #80 |
Senior Member
Join Date: March 2, 2009
Location: Orlando
Posts: 936
|
Dis be da debil...hehehe, bet you wish I showed you the other side.
|
August 21, 2009, 12:03 AM | #81 |
Senior Member
Join Date: March 2, 2009
Location: Orlando
Posts: 936
|
You can kind of see from this pic that the wedge isn't sticking out much.
|
August 21, 2009, 12:10 AM | #82 |
Senior Member
Join Date: December 4, 2005
Location: Mojave Desert, CA
Posts: 1,195
|
Clembert that vise is what bent that brass tool... You should try hittin' the other one you have with a steel ball peen hammer that has some weight to it.
The tool is made to hit with a straight blow the side load of the vist was too much for the brass. How much you got into that Lawman with a stuck wedge? I do have a new unfired Pietta 1851 Navy steel frame in .44 cal. if something were to happen that you've had enough let me know. I've had this one for 9 years never shot it. I just realized yer's ain't the Lawman in .44 it's the .36 Navy sorry....
__________________
"I Smoke Black Powder" "Favor an 1858 Remington" SGT. Smokin' Gun, Mosby's Rangers 43rd Virginia Cavalry C.S.A. SASS# 19634, ... Admin:http://blackpowdersmoke.com/oldcoots/index.php Last edited by Smokin_Gun; August 21, 2009 at 12:17 AM. |
August 21, 2009, 09:09 AM | #83 |
Senior Member
Join Date: November 2, 2007
Location: Northern Orygun
Posts: 4,923
|
ClemBert, do you have access to an arbor press? I have encountered one wedge that would not move with hammer and punch. The arbor press took it out like a hot knife through butter.
|
August 21, 2009, 09:11 AM | #84 |
Senior Member
Join Date: March 2, 2009
Location: Orlando
Posts: 936
|
Just to be clear...the tool below bent when struck hard with a hammer.
The above pictured brass punch is not what you are seeing in the picture below. The homemade punch below and to the left is what you saw in the vice. |
August 21, 2009, 09:18 AM | #85 | |
Senior Member
Join Date: March 2, 2009
Location: Orlando
Posts: 936
|
Quote:
|
|
August 21, 2009, 04:43 PM | #86 |
Junior Member
Join Date: August 15, 2009
Posts: 10
|
I also cannot remove the wedge from my 1851 Pietta Colt Navy. Will try what is suggested here...
|
August 23, 2009, 01:23 PM | #87 |
Senior Member
Join Date: July 6, 2006
Location: Planet Earth
Posts: 976
|
Arbor press 49.00 from harbor freight. It works for many other things also.
__________________
If ye love wealth better than Liberty, the tranquillity of servitude than the animated contest of Freedom, go from us in Peace. We ask not your counsel or Arms. Crouch down and lick the hands which feed you. May your chains sit lightly upon you, and may posterity forget that you were our countrymen. --Samuel Adams--<*ixoye>< |
September 14, 2009, 10:21 PM | #88 |
Senior Member
Join Date: March 2, 2009
Location: Orlando
Posts: 936
|
I thought I'd give an update on that rascally wedge from hell. I was able to get to ClemBert's shootin' range today to shoot the ever livin' crap out of the Pietta 1851 Navy. I went with 25 grains of 777 without a wad to loosen that puppy up. When I got home I took both of my brass punches and proceeded to bend them both....big surprise huh? Now they both look like the one on the right.
Now it was time to break out the wedge destructo tool...a big STEEL punch. With a big ol' framing hammer I hit that sucker once...no movement. I reset the punch then took another big swing and to my delight that wedge popped free. Hallelujah!!! Got that puppy cleaned up in a hot soapy bath and baked her dry. I changed out the factory nipples with some Treso bronze nipples. Anti-seize grease on both the nipple threads and the wedge from hell. Fortunately the wedge didn't suffer too much damage from the steel punch. There's just a round dent in it where the punch made contact but not too noticeable. Thanks for everyone's suggestions and encouragement through this saga. |
September 15, 2009, 03:51 AM | #89 |
Senior Member
Join Date: March 2, 2009
Location: Northeast for now
Posts: 266
|
Great!!! can you tell if the wedge is contacting the front of the arbor slot, and the bacK of the barrel slot, or is it contacting the front and back of just the arbor slot?
__________________
Olmontanaboy No good deed goes unpunished. A loaded gun, a faithful dog,,, consider yourself lucky. |
September 15, 2009, 09:31 AM | #90 |
Senior Member
Join Date: April 14, 2009
Location: Sunny Southern Idaho
Posts: 1,909
|
Good gravy, Clem, you ought to sell the movie rights to this saga!
__________________
Well we don't rent pigs and I figure it's better to say it right out front because a man that does like to rent pigs is... he's hard to stop - Gus McCrae |
September 15, 2009, 04:15 PM | #91 | |
Senior Member
Join Date: March 2, 2009
Location: Orlando
Posts: 936
|
Quote:
|
|
September 16, 2009, 12:38 AM | #92 |
Senior Member
Join Date: December 4, 2005
Location: Mojave Desert, CA
Posts: 1,195
|
Congrads Clembert... :O)
__________________
"I Smoke Black Powder" "Favor an 1858 Remington" SGT. Smokin' Gun, Mosby's Rangers 43rd Virginia Cavalry C.S.A. SASS# 19634, ... Admin:http://blackpowdersmoke.com/oldcoots/index.php |
September 16, 2009, 01:06 PM | #93 |
Senior Member
Join Date: March 15, 2005
Location: Central Connecticut
Posts: 3,166
|
There's always comments about the Italian gorillas that pound those wedges in too tight.
But I wonder if the wedges aren't being forced in too tight because they're using a shop press? http://www.northerntool.com/webapp/w...Product%20Page Especially since they assemble so many guns at a time, wouldn't want to damage the new wedges by manually pounding them in and a press would apply consistent pressure. To top it off both of Clembert's pistols had the exact same problem with the brand new wedge being stuck. And as to whether it's right or wrong to think that Pietta could easily back off on the wedge installation pressure, maybe they feel that much pressure is necessary to form fit the wedge during it's first insertion by using a fixed amount of force. I still think that a penny's worth of grease applied at the factory would have helped to remove it. Last edited by arcticap; September 16, 2009 at 01:16 PM. |
September 16, 2009, 03:19 PM | #94 |
Junior Member
Join Date: August 15, 2009
Posts: 10
|
I am pretty sick of seeing "Italian Gorilla" in this thread.
He may be a little heavy with the hammer but your ape fingers are a little heavy with the keyboard. ease up. |
September 17, 2009, 01:24 AM | #95 |
Senior Member
Join Date: December 4, 2005
Location: Mojave Desert, CA
Posts: 1,195
|
Kapeeesh?
__________________
"I Smoke Black Powder" "Favor an 1858 Remington" SGT. Smokin' Gun, Mosby's Rangers 43rd Virginia Cavalry C.S.A. SASS# 19634, ... Admin:http://blackpowdersmoke.com/oldcoots/index.php |
September 18, 2009, 08:32 PM | #96 |
Senior Member
Join Date: August 6, 2009
Location: South Carolina
Posts: 709
|
A brand called Break Free. Their add reads--"frees everything but a convict. I really don't know where to get it but maybe google it--just a suggestion
WBH |
September 21, 2009, 06:37 PM | #97 |
Junior Member
Join Date: October 27, 2006
Location: North of Boston, Massachusetts
Posts: 2
|
I just finished going through the same ordeal with a brand new Cabela's (Pietta) 1860 Colt Army (steel). I too have the bent punches and brass rods, flattened brass screws, split dowels, bent pennies and blood blisters on my hands from being pinched by the punches. That wedge would not move. ClemBert I feel your pain. I have another 1860 being shipped to me as I write this. Hopefully things work out better this time. Mr. Pietta we need to talk. NOTE: I ordered a Pietta 1858 Remington at the same time and the pistol is flawless.
|
September 21, 2009, 06:53 PM | #98 |
Senior Member
Join Date: February 9, 2007
Posts: 3,101
|
Time to stop thinking in terms of engineering and start thinking like a mechanic. Replace the wedge; do not attempt to save it or be nice to it any more
Make a wooden cradle to hold the revolver firmly in a clamshell, take the whole thing to a milling machine and mill a hole in the wedge. Then when you whack it the metal has a place to "give" to Then get another wedge- on Pietta's dime When you get the wedge out, you'll be able to see what the problem was. My Pietta's wedge never had any problems so I don't have any insights as to the cause |
September 21, 2009, 07:16 PM | #99 |
Senior Member
Join Date: September 16, 2007
Posts: 712
|
robhod
I had forgot that Pietta has a website for customer service. I had bought a Remington pocket new old stock and the front sight was loose, they sent me a new front sight. Maybe a blogging of the site with the wedge complaints will result in a change!!!! or a suggested fix!!
|
September 25, 2009, 01:52 AM | #100 |
Senior Member
Join Date: February 24, 2009
Posts: 727
|
I just got my first open-top cap-and-ball revolver a few days ago. It is an 1860 Pietta. The wedge was fairly tight, but not like the one in this thread, thank goodness!
Anyhow, this being my first "wedged" gun, do they ever loosen up to the point where you can remove and replace them by hand alone? I remember seeing Clint Eastwood change a cylinder with no tools in a movie once. And then there was Tuco in "The Good, The Bad, and The Ugly" swapping several Colt barrels in the gun store. So what's the true scoop? Last edited by Model-P; September 25, 2009 at 04:05 AM. |
Thread Tools | Search this Thread |
|
|