December 27, 2012, 08:56 PM | #1 |
Member
Join Date: November 16, 2011
Location: northeast ms.
Posts: 54
|
Lee hand prime??
I have one of the old type lee hand prime tools, it has a 38/357 shell holder. My queswtion is, can I get a 44 cal. shell holder for it or was it only made for a certain caliber? thanks
|
December 27, 2012, 09:18 PM | #2 |
Senior Member
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 609
|
__________________
U.S. Army Veteran NRA Certified Range Officer |
December 27, 2012, 09:20 PM | #3 |
Senior Member
Join Date: December 15, 2012
Location: Great Northwest
Posts: 222
|
Yes you can get a whole set of shell holders for that hand prime tool, I have the set but wore my hand prime tool out and ended up buying the RCBS bench mount priming tool so may never use the lee hand prime shell holders again
|
December 27, 2012, 09:55 PM | #4 | |
Senior Member
Join Date: December 24, 2008
Location: Loveland, CO
Posts: 1,476
|
Quote:
|
|
December 27, 2012, 10:01 PM | #5 |
Senior Member
Join Date: December 15, 2012
Location: Great Northwest
Posts: 222
|
The shell holders I have for the lee hand prime tool I use to have are the thin type that slide in and out, I wasn't aware of an older version that threaded and screwed? Not trying to butt in here just curious
|
December 27, 2012, 10:11 PM | #6 | |
Senior Member
Join Date: December 24, 2008
Location: Loveland, CO
Posts: 1,476
|
Quote:
I read lots of posts where folks break the lever on all versions. I can understand that since they are not forged steel, but I have primed many 10's of thousands and never broken any of the parts. But I always make sure the contact points well lubed and never abused them by trying to prime an pocket that was crimped without swaging first. |
|
December 27, 2012, 10:37 PM | #7 |
Member
Join Date: November 16, 2011
Location: northeast ms.
Posts: 54
|
I guess mine is the oldest type, the shell holder screws onto the body, I dont know if this type is available from lee.
|
December 27, 2012, 10:46 PM | #8 |
Senior Member
Join Date: December 15, 2012
Location: Great Northwest
Posts: 222
|
My lee hand prime tool lasted many years and primed several thousand cases, mine didn't actually break, it wore from lack of care and it wouldn't seat the primer below flush anymore (I didn't keep it lubed) I could have bought the replacement parts to fix it but chose to retire it and ended up buying the RCBS bench mount priming tool, like I said I stil have the shell holder set for it (little red flat slip top box) and a few extras that don't come with the kit. I really liked the tool and got several years of use out of it, you can't wear the shell holders out
|
December 27, 2012, 11:05 PM | #9 |
Senior Member
Join Date: June 30, 2009
Location: dallas
Posts: 773
|
My experience combines jepp2 and solocam 72. Mine wore out to the point it would not fully seat the primer. I epoxied on a thin washer to the plunger and was back in business until I got to 10,001 and the handle broke. I just bought a new/used one on ebay. There are usually several for sale, some brand new and some gently used. I liked the tool and really didn't want to switch to something else.
|
December 28, 2012, 05:36 AM | #10 |
Senior Member
Join Date: December 15, 2012
Location: Great Northwest
Posts: 222
|
I have to admit I miss my little lee hand prime tool, maybe I will find another one like I had somewhere down the road and put my shell holders back to use, it was simple and worked very well. Mine was given to me by a friend that bought it new and ended up not liking it, I don't think he primed over 50 cases with it.
|
December 28, 2012, 07:12 AM | #11 |
Member
Join Date: June 21, 2006
Location: Eastern Ohio
Posts: 94
|
Once in a conversation when ordering some items from Lee the rep told me that you can send in your lee hand primer and they would send you another one.
Not sure of the reason why they would do this as i was not really paying attention, just wanted to order my other parts. If anybody has issues with their's might be worth a phone call to Lee. |
December 28, 2012, 08:43 AM | #12 | |
Senior Member
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 609
|
Quote:
http://castboolits.gunloads.com/show...l-holder-sizes
__________________
U.S. Army Veteran NRA Certified Range Officer |
|
December 28, 2012, 10:32 AM | #13 |
Senior Member
Join Date: December 19, 2012
Posts: 297
|
Shell Holders
I have and use the same old Lee Priming tool that uses screw in shell holders.I was able to find screw in shell holders on E_Bay.I bought two but had to pay 10 bucks each.I've also seen them from time to time at gun shows.Good luck ,biker
|
December 28, 2012, 12:26 PM | #14 |
Member
Join Date: November 16, 2011
Location: northeast ms.
Posts: 54
|
this type of shell holder is no longer available from Lee, (per e-mail I just received from them)
|
December 28, 2012, 04:23 PM | #15 |
Senior Member
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,930
|
Well the New Auto Prime XR is not that expensive, and the shell holder set is about $15 or less from most places. The handle on the new one will not break. A friend of mine tried to break one pushing too hard on a crimped primer pocket. He managed to ruin a primer, and had a hard time getting the brass out of the shell holder. The tool still worked fine after that. I have one myself. I will say be gentle sliding the lid on, and off. The plastic tabs get brittle, and break if you do not. I still use mine it has primed many thousands of rounds, and is still going strong.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you. |
December 28, 2012, 05:03 PM | #16 |
Senior Member
Join Date: May 20, 2001
Location: Oshkosh wi.
Posts: 3,055
|
For the young-uns here that have never even heard of the early lee hand primers. They worked quite well, you varied the depth of the primer seating by how far the shell holder was screwed into the body. The ultra fine threads were easy to get cross-threaded, so you wore that out before the cam on the handle wore out. What I did was buy a body along with a shell holder, then leave them assembled. Since this was very early in my reloading career, I only had 3 calibers that I reloaded, two took the same shell holder. (308 and .243).
__________________
The more people I meet, the more I love my dog They're going to get their butts kicked over there this election. How come people can't spell and use words correctly? |
December 28, 2012, 05:13 PM | #17 |
Senior Member
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 609
|
Over the last few years I've been able to pick up a few of these older hand primers for my most reloaded calibers except for one, and for that I use a K & M hand primer.
I had one that came with the threads in very bad shape. Being as I wanted it for a specific caliber I used JB Weld and glued the shell holder in place. Its held for thousands of rounds so far.
__________________
U.S. Army Veteran NRA Certified Range Officer |
December 28, 2012, 06:20 PM | #18 |
Senior Member
Join Date: December 15, 2012
Location: Great Northwest
Posts: 222
|
Snuffy, thanks for the picture, I have never seen one like that in my travels.
|
December 28, 2012, 06:31 PM | #19 |
Senior Member
Join Date: December 26, 2004
Location: Louisville KY
Posts: 13,805
|
Looks like a Ram Prime with a handle. I'd much prefer that over that POS XR I foolishly bought.
|
December 28, 2012, 07:29 PM | #20 |
Senior Member
Join Date: May 29, 2011
Location: Fort Worth
Posts: 500
|
That was my first priming tool in the late 60's. Still have it and it still works very well. I think I have 38/357, 45 Colt, and 45ACP shellholders. I think the 45ACP works for all the 30-06 based brass also.
IIRC they cost about $3.50.
__________________
Education teaches you the rules, experience teaches you the exceptions (Plagiarized from Claude Clay) |
Thread Tools | Search this Thread |
|
|