May 14, 2012, 09:26 PM | #1 |
Junior Member
Join Date: May 14, 2012
Posts: 4
|
In over my head
All right all you experienced people out there...
I have set out on my own and am learning the art of reloading after I had a ridiculous six months and purchased a Mosin, an Arisaka, 1903 Springfield, Mauser, and Enfield. Once I started I could not stop. I am reloading for them and tried out the famous 16gr 2400 load with sierra 150 gr sptzr. At 100 yards I was shooting like a foot or two low? What did I do wrong? Also, the accuracy on my Enfield is ridiculous. The front sight looks slightly bent to the left??? but not sure. Are these replaceable or adjustable? Just hoping to connect with some serious expertise on this forum and learn the art of reloading for these rifles. |
May 14, 2012, 09:51 PM | #2 |
Senior Member
Join Date: May 11, 2007
Location: NSW, Australia
Posts: 909
|
Come and join us at the Enfield forum in my signature - if you search our forum you will find many answers regarding stocking up and accurizing an Enfield.
Tiki.
__________________
The Lee Enfield forums - http://www.surplusrifleforum.com/viewforum.php?f=27 Surplus Rifle Forums - http://www.surplusrifleforum.com/index.php |
May 14, 2012, 09:57 PM | #3 | |
Senior Member
Join Date: November 29, 2007
Location: Everett, WA
Posts: 6,126
|
Quote:
All of the rifles shoot about 2" low? |
|
May 14, 2012, 10:17 PM | #4 | |
Junior member
Join Date: October 4, 2007
Location: All the way to NEBRASKA
Posts: 8,722
|
Quote:
..... If you have a slow bullet, it will fall more at a given range than a fast one, all else being equal, because it is in the air longer, and gravity is pretty darn constant, here on earth. On what planet do they think that heavy .357 magnum data is a great idea in big milsurp cases? Where I'm from, 4895 and 4064 are popular in milsurp cartridges....... |
|
May 15, 2012, 08:40 AM | #5 |
Senior Member
Join Date: October 13, 2008
Location: Northern Virginia
Posts: 407
|
Ditch the 2400, it's use for those rifle calibers is with cast bullets at lower velocities.
4895, 4064 are good. Varget's a great all propose rifle powder. 4320 and 4895 are my favorites.
__________________
"And remember, Abraham Lincoln didn't die in vain, he died in Washington D.C." - Firesign Theatre |
May 16, 2012, 11:18 PM | #6 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
Can this small voice in the wilderness suggest that getting a decent loading manual might be a good idea? The 7.62x54R might not be in there, but .30-'06, 8x57 and .303 British should be.
Bumnote is right on the 2400 load; it is suitable for cast bullets with gas checks, not for jacketed bullets. Jim |
May 16, 2012, 11:35 PM | #7 |
Senior Member
Join Date: October 25, 2001
Location: Alabama
Posts: 18,453
|
Some old guy named Whelen had the idea that a reduced load could be real handy. He used jacketed bullets so as to not mix fouling between lead and copper for light and heavy loads. But he tweaked loads so his light load would shoot to the 200 yard sight setting at maybe 25 yards. Small game hunting.
So the first question to the OP is never mind about WHERE the underloads hit, do they GROUP? |
May 17, 2012, 02:50 PM | #8 |
Junior Member
Join Date: July 9, 2011
Posts: 9
|
Sounds like my story but I'm casting, I did this in a years time I have 9 rifles 3pistols my wife does not get it, I even bought her a 22 for our 30th anniversary and took her to the range LOL.
|
May 19, 2012, 01:58 PM | #9 |
Senior Member
Join Date: February 11, 2010
Location: East Texas USA
Posts: 1,805
|
I shoot a 2400 FPS load in my Yugo 24 47, but it takes 44.0 Grains of IMR 4895 to achieve this with a Speer Hotcore 150 Grain Spitzer Bullet.
The 44.0 Grain Powder Charge is the starting load in my Complete Load Book for the 8MM Mauser. Im satisfied with that load, no need to waste more powder in an iron sighted Rifle. To the OP, be carefull with your reloading for the .303 Enfield. The chambers often run a little long on those, and sometimes the headspace is questionable, its best to only full leingth resize new cases, then after firing in your Rifle, neck size only. let the brass expand to fit your chamber, and you will be less likely to rupture cases. Good Luck. |
May 20, 2012, 10:50 AM | #10 |
Senior Member
Join Date: August 1, 2010
Location: Tampa Bay
Posts: 4,556
|
I shoot the Mosin 91/30 sporter I modded at 600 yards regularly.
It takes the exact same accuracy load as our .308... In the .308, we use the 175 grain SMK over 43.5 grains of Varget. In the 7.62 x 54R, it's the 174 grain SMK (in .311) over the same load. I prefer the "extreme" powders like Varget, H4350 because they are unaffected by temperature. |
May 20, 2012, 05:47 PM | #11 | |
Senior Member
Join Date: April 2, 2002
Location: Falcon Colorado
Posts: 256
|
Quote:
|
|
Thread Tools | Search this Thread |
|
|