|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
October 3, 2009, 10:45 AM | #101 |
member
Join Date: June 12, 2000
Location: Texas and Oklahoma area
Posts: 8,462
|
There is constructive possession under the 1934 NFA. All Thompson said was that if there is a possible legal use and a possible illegal use, then the rule of lenity says that the court will assume the possessor was going to do the legal thing and not the illegal one.
However, if you have no legal use for the parts in question (example: a 1911 pistol, a 1911 shoulder stock and only a pistol barrel), that is pretty much a textbook case of what ATF considers constructive possession of an SBR. Another common occurence that ATF also considers constructive possession of an SBR (or at least they have written letters to that effect) is as follows: 1. You have a single legally registered NFA-compliant SBR AR15. 1. You have a single non-NFA AR15 rifle. 3. You have more than one short barrelled SBR upper for the AR15. |
October 3, 2009, 09:11 PM | #102 | |
Senior Member
Join Date: August 30, 2009
Location: Northern AZ
Posts: 7,172
|
Quote:
Is that still considered "constructive possession?" |
|
October 4, 2009, 09:08 AM | #103 |
member
Join Date: June 12, 2000
Location: Texas and Oklahoma area
Posts: 8,462
|
Well, I would argue no since you do not control all of the parts to "make" a short-barrelled rifle. I'm not sure what ATF would argue since there seems to be a complete lack of logic in some of their decisions.
|
October 4, 2009, 11:16 AM | #104 |
Senior Member
Join Date: August 30, 2009
Location: Northern AZ
Posts: 7,172
|
Finally! An answer! Thanks!
|
October 4, 2009, 05:13 PM | #105 |
member
Join Date: June 12, 2000
Location: Texas and Oklahoma area
Posts: 8,462
|
Like I said, that is an answer; but it may not be the same conclusion ATF reaches. You should ask ATF for an answer in writing to be sure.
|
October 5, 2009, 04:22 PM | #106 |
Senior Member
Join Date: August 6, 2009
Location: Albuquerque
Posts: 2,832
|
One question - what determines the barrel length for a revolver by ATF SBR definition? A friend of mine has a (probably Italian copy of ) Colt Buntline and was thinking about putting a stock on it. If you measure the "traditional" way, the round part sticking out of the frame, you get 15 3/4 inch, if you measure from the air gap it's 16 1/4. SBR or not, that is the question.
__________________
I used to love being able to hit hard at 1000 yards. As I get older I find hitting a mini ram at 200 yards with the 22 oddly more satisfying. |
October 5, 2009, 05:54 PM | #107 |
Junior member
Join Date: January 23, 2008
Location: MI
Posts: 1,398
|
Revolvers are weird but I think they go from firing pin to muzzle with action closed.
A lot of game departments use this for barrel length measurements, which actually benefits wheelguns because the industry only includes the rifled portion whereas the DNR includes the cylinder itself, getting an additional 1.6 inches or so of "barrel" length. States that have a 5.5 inch barrel on pistols means you can use a .357 Mag wheelgun with 4 inch barrel because of the measurement criteria; 1.6+4=5.6 and you're good to go. |
October 6, 2009, 12:26 AM | #108 |
Senior Member
Join Date: March 20, 2008
Posts: 442
|
Federally, most barrels are measured from breechface with the action closed (and cocked if applicable) to the end of the muzzle (including any permanent attachments, with permanent being welded, blind pinned, etc., not just threaded on)
I'm honestly unsure of how to measure a revolver, by Federal standards. mapsjanhere The way you describe "traditional" measurement is just plain wrong - the barrel continues into the receiver. Measured conservatively (not into the cylinder) it's still over 16" for the barrel. As long as overall length is 26" or more with the stock, it's good to go. |
October 8, 2009, 06:55 PM | #109 |
Senior Member
Join Date: August 30, 2009
Location: Northern AZ
Posts: 7,172
|
Revolvers are measured from the beginning of the forcing cone to the end of the muzzle. The chambers are not included
This was one of the arguments that the Germans used after WWI to circumvent the Treaty of Versailles, i.e. that since chambers of revolvers were not included in the measurement of barrel length on a handgun, it should not be so on an auto either. |
|
|