The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools Search this Thread
Old March 7, 2011, 11:02 PM   #1
76r
Member
 
Join Date: November 14, 2006
Location: Northern Alberta, Canada
Posts: 23
S&W .455 Colt

I have an old Smith & Wesson revolver. The barrel is stamped ".455 Colt". I have old casings stamped ".455 Colt". However, I can't find any info on this caliber...just ".455 Webley".
Can you tell me anything about this caliber, history, reloading specs, etc?
76r is offline  
Old March 8, 2011, 12:50 AM   #2
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,374
The .455 Colt is actually the old British .455 Webley Mk I cartridge, which started out as a blackpowder round in 1892.

When the switch was made to Cordite (smokeless) powder in 1897, the case was shortened a bit, a bout .1 inches, to create the .455 Webley Mk II.

Ballistically the two rounds were pretty much the same.

Colt, Smith & Wesson and others chambered the .455 Webley Mk I as the .455 Colt up until about World War I, primarily for sale in Canada. Ammunition was loaded in the United States up through to about 1930.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old March 8, 2011, 04:15 AM   #3
gyvel
Senior Member
 
Join Date: August 30, 2009
Location: Northern AZ
Posts: 7,172
If you get desperate for ammo, you can make .455 ammo from .45 Colt cases by shortening them and thinning the rim.
gyvel is offline  
Old March 8, 2011, 11:40 AM   #4
76r
Member
 
Join Date: November 14, 2006
Location: Northern Alberta, Canada
Posts: 23
Thanx for the responses.
I can get (when available) loaded .455 Webley cartridges by Fiocchi thru a dealer here in Canada, but I wasn't sure if I was looking at the same dog!
I also wanted to be sure I could follow .455 Webley reloading specs as I have only seen for that cartridge, never .455 Colt. And although it is not a heavy () round, I didn't want to 'just give her a try' sort of thing!
76r is offline  
Old March 8, 2011, 11:50 AM   #5
76r
Member
 
Join Date: November 14, 2006
Location: Northern Alberta, Canada
Posts: 23
I'm not sure of the age of this firearm, but it is apparently an old RCMP service revolver (c/w I.D. stampings just ahead of the cyliinder on the barrel). It has been a 'safe queen' in the family scince 1975 (+-) and is in real nice shape.
Im not really interested in firing it, I just want ammo to complete the arrangement!
76r is offline  
Old March 8, 2011, 12:26 PM   #6
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,374
What's the serial number off the bottom of the grip, and someone here will be able to pin down a year of manufacture for you.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old March 8, 2011, 03:20 PM   #7
gyvel
Senior Member
 
Join Date: August 30, 2009
Location: Northern AZ
Posts: 7,172
Actually, .455 Colt was loaded for years by C.I.L. under the "Dominion" brand if I recall. Since you are in Canada, you should be able to find some of those floating around to compliment your revolver.

In years past, it was either that or corrosive British surplus. I used to grab every box I could find, either on dealers' shelves or at gun shows since the C.I.L. stuff was reloadable.

Edit: Yes, it was "Dominion" (another name used by C.I.L.) and not "Canuck."

Last edited by gyvel; March 12, 2011 at 05:43 AM.
gyvel is offline  
Old March 8, 2011, 03:47 PM   #8
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,374
I think CIL dropped .455 Colt in the late 1950s or early 1960s.

I'd suspect that the supply is drying up, if it hasn't already.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old March 8, 2011, 04:43 PM   #9
76r
Member
 
Join Date: November 14, 2006
Location: Northern Alberta, Canada
Posts: 23
The casings I have are 'Dominion'. (I'd bet that's a 'C.I.L.' label; I seem to remember shotshell cartons of both names bearing the same label/logo; 'Imperial' as well I think; anyway they sound Canadian with the 'Monarchy' reference )
76r is offline  
Old March 12, 2011, 08:21 PM   #10
76r
Member
 
Join Date: November 14, 2006
Location: Northern Alberta, Canada
Posts: 23
Mike,
The serial number is 33-6*7.
Thanx

Last edited by 76r; March 13, 2011 at 11:45 AM.
76r is offline  
Old March 12, 2011, 09:31 PM   #11
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,374
CIL was Canadian Industries Limited.

IIRC the company was organized after World War II and took over operations at the old Dominion Arsenal.

That serial number very likely means that it's a .455 Mark II Second Model, manufactured between 1915-1917. The majority of these guns went to the British, but over 15,000 went to Canada.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old March 13, 2011, 11:44 AM   #12
76r
Member
 
Join Date: November 14, 2006
Location: Northern Alberta, Canada
Posts: 23
Thanx for the info.
I appreciate your help.
76r is offline  
Old March 13, 2011, 01:34 PM   #13
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,374
Thinking about this some more...

I don't know why the gun, if made for Canada under a WW I blanket contract, would have been chambered for the .455 Colt, which was the longer case and was obsolete as a military use item...

Tell me, when the cylinder is closed, does the ejector rod fit in a protected shroud (housing), or is it exposed along the bottom of the barrel with the front supported by a lug?
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old March 15, 2011, 02:24 PM   #14
76r
Member
 
Join Date: November 14, 2006
Location: Northern Alberta, Canada
Posts: 23
Mike,
The ejector rod is just supported at the front when closed; not full length shroud.
There are 2 crossed flags (RCMP symbols)? stamped on the back of the cylinder, visible when open. And another stamp of the same, on the left side of the barrel just ahead of the cylinder. Below this 2nd stamp, on the cylinder mount is a large X with a - thru it.
76r is offline  
Old March 15, 2011, 03:57 PM   #15
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,374
OK, it's definitely a second model.

Don't know what the crossed flags might be, I'm not at all familiar with Canadian markings.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old March 15, 2011, 09:15 PM   #16
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
I am not sure about Canadian marks either, but crossed pennants is the British military proof/acceptance mark. If the gun was in British service it should also have a broad arrow, the British property mark. A "C" with a broad arrow in it, is the Canadian property mark.

Just FWIW, CIL once turned out a whole batch of that .455 headstamped ".455 CLOT". Some red faces there, I am sure.

Jim
James K is offline  
Old March 15, 2011, 09:44 PM   #17
76r
Member
 
Join Date: November 14, 2006
Location: Northern Alberta, Canada
Posts: 23
Thanx again for the info posts. I appreciate it.
76r is offline  
Old March 16, 2011, 02:54 PM   #18
RickB
Senior Member
 
Join Date: March 1, 2000
Location: Boise, ID
Posts: 8,511
Quote:
That serial number very likely means that it's a .455 Mark II Second Model, manufactured between 1915-1917. The majority of these guns went to the British, but over 15,000 went to Canada.
I have one of these, and it is not marked .455 Colt, but merely .455. Mine has been converted to .45 ACP, and the second "5" in .455 has been X-d out and an "AR" (Auto Rim) stamp added. I have WWII-era Canadian military ammo, and it does fit in my Webley Mk. I, which makes sense, since the later cartridge has a shorter case. My S&W has a M1917 cylinder fitted, so I can't make any determination about the original chambering.
RickB is offline  
Old April 7, 2011, 11:58 AM   #19
Dave Anderson
Senior Member
 
Join Date: March 4, 2011
Posts: 313
The markings seem to be military acceptance stamps. The RCMP and its predecessors (RNWMP and NWMP) were never issued the S&W in .455. First calibers issued were .450 Adams, then .476 Enfield. The Colt New Service in .45 Colt was adopted around 1905 and was (so far) the longest-serving issue sidearm, remaining in service for 49 years until 1954.

In 1954 the RCMP adopted the S&W M&P in .38 Special with 5" barrel. It remained in service for some 40 years until replaced as the standard sidearm for uniformed officers by the 9mm S&W 5946 in the 1990s.

The .455 was used in British service revolvers prior to and during WW I. When British gunmakers couldn't begin to meet demand as the military expanded during the war, Britain contracted with S&W and Colt for revolvers, and as a matter of logistics specified they be in .455. Since Canadian troops were fighting alongside British forces from 1914 on it made sense to use the same cartridge.
Dave Anderson is offline  
Old April 7, 2011, 06:43 PM   #20
76r
Member
 
Join Date: November 14, 2006
Location: Northern Alberta, Canada
Posts: 23
Thanx for the additional info. It sounds like the consensus is it is an ex military sidearm; not RCMP then.
76r is offline  
Old September 15, 2011, 06:27 PM   #21
rabbit
Junior member
 
Join Date: September 15, 2011
Posts: 37
hi , can you please post a picture i would really like to see what a 455 S&W looks like , rabbit
rabbit is offline  
Old September 15, 2011, 08:57 PM   #22
RJay
Senior Member
 
Join Date: November 2, 2005
Location: Arizona
Posts: 1,936
rabbit, it looks just like a S&W Service Model of 1917. There are no special features
__________________
Ron James
RJay is offline  
Old September 15, 2011, 09:35 PM   #23
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
The RNWMP/RCMP used .45 Colt, but the Canadian army, as part of the British Empire and Commonwealth forces, used the .455.

Jim
James K is offline  
Old September 16, 2011, 08:38 PM   #24
76r
Member
 
Join Date: November 14, 2006
Location: Northern Alberta, Canada
Posts: 23
Rabbit, if you're thinking that it is similar to Dirty Harry's S&W .44mag, only bigger and badder ...you would be badly mistaken!
It has a very thin barrel due to the low power/velocity. I have bounced bullets back off of wood timbers!
I will post a pic if you still are curious though.
76r is offline  
Old September 19, 2011, 01:52 PM   #25
rabbit
Junior member
 
Join Date: September 15, 2011
Posts: 37
great , I luv ond sixguns and auto also.
rabbit
rabbit is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:02 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.12138 seconds with 11 queries