April 27, 2011, 10:44 PM | #1 |
Junior Member
Join Date: April 19, 2011
Location: Houston, TX
Posts: 3
|
Remington 51
I have just obtained from my father's estate and know nothing about the gun.
Serial Number is PA24382 and has Remington UMC on the grip. I would like to know date of manufacture and general information, and also of course it's potential value. It does have one clip. Thanks Caliber is 380ACP and the condition is good. Fires well. I think that it is in good condition. Two photographs are attached to my post in the The SemiAuto Forum. http://thefiringline.com/forums/atta...0&d=1303306059 http://thefiringline.com/forums/atta...1&d=1303306059 Thanks |
April 28, 2011, 11:59 AM | #2 |
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
|
Some information here
http://en.wikipedia.org/wiki/Remington_51 As far as getting information regarding your personal piece, you can send info to the person who manages this page http://www.remingtonsociety.com/rsa/research/Model51
__________________
Never try to educate someone who resists knowledge at all costs. But what do I know? Summit Arms Services |
April 28, 2011, 03:09 PM | #3 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
Every time someone asks about the Remington 51, I have to warn against trying to pry off the grips, as they are easily broken. If you must remove the grips, push the grip safety pin (at the bottom rear of the butt) in flush on one side and slide the grip on that side down and off, then do the same on the other side.
Jim |
April 28, 2011, 05:57 PM | #4 |
Junior Member
Join Date: April 24, 2011
Posts: 5
|
I have one.
They were way ahead of their time. This gun was built using added ingenuity. John Moses Browning had copyrighted all of the good gun designs, so it was very tough for Pedersen to make a pistol that did not infringe on Brownings patents. I shoot mine on occasion. Its a blast to shoot. They have 2 different slide variations. Enjoy it. |
April 28, 2011, 08:25 PM | #5 |
Senior Member
Join Date: September 19, 2008
Posts: 4,678
|
IIRC, the DOM of the OP's P-51 is about 1922.
. |
April 29, 2011, 06:17 AM | #6 |
Senior Member
Join Date: December 20, 2008
Location: Pittsburgh PA
Posts: 2,863
|
Judging by the pics, the gun looks badly worn and possibly pitted with rust. The 380 version is more common than the 32 version by a long shot. Given the condition and caliber, I put the value at $250 to $300. Even though they're rather uncommon today, they're not rare, partly because many survived due to their high quality. Approx 65k were made IIRC, with 55k being 380 and the rest being 32. I'm lucky enough to own a 32 and the 380 I had I gave to my uncle as a Christmas gift.
__________________
Winchester 73, the TFL user that won the west Last edited by Winchester_73; April 29, 2011 at 08:18 AM. |
April 29, 2011, 07:49 AM | #7 |
Senior Member
Join Date: April 5, 2009
Posts: 487
|
I recently picked up a Model 51 that is from the second year of production, very early serial number and very nice condition. This is one beautiful pistol, both from a cosmetic point of view and from a design point of view. I love it and hope that yours is as functionally nice as mine is. Mine is early enough that it has a HORRIBLE trigger pull but that was apparently designed out in the models produced later. This is a well known issue with the earliest serial numbers.
The only bad thing is that finding replacement springs and such can be a problem. Wolff gun springs makes springs for lots of pistols and rifles but the Model 51 is not one of them. Enjoy your pistol. |
April 29, 2011, 11:42 PM | #8 |
Senior Member
Join Date: August 30, 2009
Location: Northern AZ
Posts: 7,172
|
Be extra cautious as to what loads you put through your gun. They're not intended for hot rounds. The rear end of the breechblock where the little roller is pinned is very fragile and prone to cracking.
|
April 30, 2011, 04:17 PM | #9 |
Senior Member
Join Date: January 25, 2005
Location: Mississippi/Texas
Posts: 2,505
|
Very cool, I've always wanted one.
__________________
"Suppose you were an idiot, and suppose you were a member of Congress, but I repeat myself." Mark Twain |
May 1, 2011, 04:41 PM | #10 |
Senior Member
Join Date: October 18, 2000
Posts: 708
|
I am buying one in .380.
Have only handled it so far. It's a pistol with a very good feel in the hand. I expect to shoot it but probably not a whole lot.
__________________
"To disarm the people (is) the best & most effectual way to enslave them." George Mason. |
April 4, 2013, 01:49 PM | #11 |
Senior Member
Join Date: January 11, 2013
Posts: 257
|
I have a Remington 51 that came with the original magazine. But a replacement magazine has given me problems in ejecting and loading a new round. I find that I have to hold the grip saftey very hard to get it to reload a new round but it still fails most of the time. The older real magazine works every time. Early in the week I went to the range and the first 10 shots worked okay but then it started not ejecting properly. Can't really tell if it's me or the gun.
J |
April 5, 2013, 11:23 AM | #12 |
Senior Member
Join Date: July 21, 2011
Location: Idaho
Posts: 7,839
|
you may be better off starting a new thread rather than resurrecting a 2 year old one. a lot of comments are going to be in regard to the OP as some are too lazy to read the entire thread(like myself) or look at date stamps.
do you have all of those problems with the original mag as well or just the replacement mag? if it's the replacement magazine only then I would suggest taking it to a skilled gunsmith and having him modify the magazine to meet the exact specifications of the original, many replacement magazines currently availiable suck in C&R guns. another thing you could try is a thorough cleaning and lubing and paying special attention to the grip safety.
__________________
ignore my complete lack of capitalization. I still have no problem correcting your grammar. I never said half the stuff people said I did-Albert Einstein You can't believe everything you read on the internet-Benjamin Franklin |
Tags |
380acp , remington 51. 380 caliber |
Thread Tools | Search this Thread |
|
|