HK-91(G3) Dissasembly

ruger45 · July 27, 2000, 01:04 AM

Well thats it Im far from the most
mechanically inclined and was wondering their was somewhere online I could get the instructions before I buy them at the next big gunshow in a month and way before I could order them from H&K.

Patriot.45

------------------
"those who sacrifice
liberty for security deserve neither"

**4V50 Gary** · July 27, 2000, 01:41 AM

1) With the muzzle pointed in a safe direction and finger off the trigger, and magazine well empty, retract the bolt to ensure that the firearm is unloaded.

2) At the lower end of the receiver, you'll find two push pins. Remove both and place them in the storage holes in the stock.

3) Holding the rifle close to the table, pull the stock straight to the rear. The recoil spring is attached to the stock and will be withdrawn from the stock.

4) If the trigger group did not already fall out, pull it back and slightly down. It should come out easily.

5) Pull the operating handle back and withdraw the bolt carrier and bolt from the receiver (the collasping operating handle snaps back into place and remains on the firearm).

6) Setting the bolt & bolt carrier assembly upright and with the bolt carrier to the right and the bolt (bottom) to the left, rotate the bolt head counterclockwise 90 degrees. It should disengage and pop up. Remove the bolt head, firing pin and firing pin spring and locking piece. No further disassembly is recommended.

Note: To reassemble the bolt to the bolt carrier, drop the firing pin and firing pin spring into the bolt carrier first. Place the locking piece over the firing pin and firing pin spring and depressing, rotate to lock into place. Then place the bolt over the locking piece and press firmly downwards. The bolt should snap right on and the rollers should be in the locked position. Rotate the bolt such that the rollers are horizontal to the bottom of the bolt carrier. Now, grabbing the bolt head, pull slightly until the locking rollers are withdrawn.

The rest of the reassembly is in reverse order.

July 27, 2000, 01:04 AM	#1
ruger45 Junior member Join Date: August 28, 1999 Posts: 500	Well thats it Im far from the most mechanically inclined and was wondering their was somewhere online I could get the instructions before I buy them at the next big gunshow in a month and way before I could order them from H&K. Patriot.45 ------------------ "those who sacrifice liberty for security deserve neither"

July 27, 2000, 01:41 AM	#2
4V50 Gary Staff Join Date: November 2, 1998 Location: Colorado Posts: 21,840	1) With the muzzle pointed in a safe direction and finger off the trigger, and magazine well empty, retract the bolt to ensure that the firearm is unloaded. 2) At the lower end of the receiver, you'll find two push pins. Remove both and place them in the storage holes in the stock. 3) Holding the rifle close to the table, pull the stock straight to the rear. The recoil spring is attached to the stock and will be withdrawn from the stock. 4) If the trigger group did not already fall out, pull it back and slightly down. It should come out easily. 5) Pull the operating handle back and withdraw the bolt carrier and bolt from the receiver (the collasping operating handle snaps back into place and remains on the firearm). 6) Setting the bolt & bolt carrier assembly upright and with the bolt carrier to the right and the bolt (bottom) to the left, rotate the bolt head counterclockwise 90 degrees. It should disengage and pop up. Remove the bolt head, firing pin and firing pin spring and locking piece. No further disassembly is recommended. Note: To reassemble the bolt to the bolt carrier, drop the firing pin and firing pin spring into the bolt carrier first. Place the locking piece over the firing pin and firing pin spring and depressing, rotate to lock into place. Then place the bolt over the locking piece and press firmly downwards. The bolt should snap right on and the rollers should be in the locked position. Rotate the bolt such that the rollers are horizontal to the bottom of the bolt carrier. Now, grabbing the bolt head, pull slightly until the locking rollers are withdrawn. The rest of the reassembly is in reverse order.