|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
August 14, 2012, 10:16 PM | #1 |
Senior Member
Join Date: May 22, 2010
Location: North East WI
Posts: 418
|
Should I keep a Lee 148 grain wad cutter mold?
I bought both a Lee 2 cavity 158 grain SWC mold (which I have loaded quite a few of this style lead bullet in the past), and a Lee 2 cavity 148 grain wad cutter mold.
I have been thinking that it may have been a dumb idea to load the wad cutters since I have never done so in the past and it is only 8 grains lighter. Do these bullets work fine in regular .38 special brass? I have read that factory loaded wad cutters have double crimped brass and seem a bit thinner in the mouth portion of the brass. I may be leaning on returning the 148 grain and buy some sort of 9mm mold instead. Any advice? |
August 15, 2012, 12:28 AM | #2 |
Senior Member
Join Date: August 4, 2005
Posts: 2,017
|
For plinking purposes, WC's are great if you intend to shoot a lot. Their original purpose was for cutting paper anyway--and they do it very well. Half the powder as the SWC adds up after a while, too. Never had a problem with them in 38spl. If you haven't tried em', do. You just might like them. I always shied away because they were just ugly as sin--until I finally decided to see for myself if they were worth anything. They have their place, just like any other bullet.
__________________
"Why is is called Common Sense when it seems so few actually possess it?" Guns only have two enemies: Rust and Politicians. |
August 15, 2012, 12:44 AM | #3 |
Senior Member
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,720
|
I shoot 2 or 3 times as many 148 DEWC's as anything else in .38 Special and .357 Magnum. I load them light for target shooting, and heavy for blasting at steel targets. The "blasting ammo" would also be a great self-defense load if you're OK with using handloads for SD.
Regular brass works just fine. I don't load them all the way flush with the case mouth, I crimp them in the crimp groove. If you try to seat them flush you might need the thinner brass (anything with the 2 lines in it, or an R-P headstamp)
__________________
"Everything they do is so dramatic and flamboyant. It just makes me want to set myself on fire!" —Lucille Bluth |
August 17, 2012, 09:43 PM | #4 |
Senior Member
Join Date: May 22, 2010
Location: North East WI
Posts: 418
|
Looks like I will keep the die and do some experimenting. I cast a good pile of beautiful 158 grain TL SWC today.
Thanks for the replies! |
August 17, 2012, 09:46 PM | #5 |
Junior member
Join Date: January 24, 2010
Location: South West Riverside County California
Posts: 2,763
|
"The "blasting ammo" would also be a great self-defense load if you're OK with using handloads for SD."
+1 Low recoil, inherent accuracy, maxium meplat, and fantastic straight-line penetration even at 800 fps. |
August 17, 2012, 09:52 PM | #6 | |
Senior Member
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,720
|
Quote:
__________________
"Everything they do is so dramatic and flamboyant. It just makes me want to set myself on fire!" —Lucille Bluth |
|
August 17, 2012, 11:07 PM | #7 |
Senior Member
Join Date: May 22, 2010
Location: North East WI
Posts: 418
|
I like the idea of inherent accuracy. Punching paper is my mail goal. I guess I also like the idea of a smaller case capacity if you will to eliminate any position sensitive powder variations.
|
August 18, 2012, 07:24 AM | #8 |
Senior Member
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,930
|
I have only shot plated wad cutters so I have little experience with them. Though I have the 158 grain TL SWC mold. I have shot thousands of them already. I load them with Trail Boss. Low recoil, very accurate, and extemely clean. The only cleaning I have to do is from the carbon due to burned bullet lube. With my 4 inch Mod 67-1 I can shoot gallon jugs at 100 yards without too much trouble. Though velocity is nowhere near the scorcher range they shoot flatter than I would have imagined.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you. |
August 27, 2012, 11:11 PM | #9 |
Senior Member
Join Date: May 22, 2010
Location: North East WI
Posts: 418
|
I cast up a whole bunch of the 148 grain wad cutters and they look fantastic. Sized and loaded a dozen with 3.0 grains of HP-38. Haven't had a chance to test them at the range however. Strange looking loads...
|
August 28, 2012, 09:46 AM | #10 | |
Senior Member
Join Date: October 28, 2006
Location: South Central Michigan...near
Posts: 6,501
|
Quote:
As for the utility of wadcutters, they are a good bullet for all .38 Spl./.357 revolver shooting for everything except perhaps long-range shooting (it is said that wadcutters lose out to semi-wadcutters at long range). My only issue with wadcutters is that they are not as easy to use with speed loaders compared to round-nose bullets. The flat front edge of wadcutters do not guide the rounds into the chambers like round nose bullets do. But at the terminal end, flat-nose bullets (wadcutters), will always out perform round nose bullets be it self-defense or rabbits. Last edited by dahermit; August 28, 2012 at 09:54 AM. |
|
August 28, 2012, 12:49 PM | #11 |
Senior Member
Join Date: February 7, 2009
Location: Southern Oregon!
Posts: 2,891
|
I really like my Lee 148 DEWC mold/bullets. I shoot a lot of "normal" (light target) loads in my .38s and .357s and for my house gun I load some with a stiff load of W231. Mine has a crimp groove at one end and I seat to the groove and use a light roll crimp or taper crimp and they are pretty consistant accurate shooters...
__________________
My Anchor is holding fast! I've learned how to stand on my own two knees... |
September 3, 2012, 12:23 AM | #12 | |
Senior Member
Join Date: May 22, 2010
Location: North East WI
Posts: 418
|
Quote:
My brother shot a dozen of these wadcutters in my 3" SP101 with no leading. He couldn't comment on the accuracy of the loads since it isn't his gun, so I will slap together another 50 to run through my security 6 before making a pile of them. Glad I kept the mould now..... |
|
Thread Tools | Search this Thread |
|
|