The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old December 5, 2009, 02:37 PM   #1
essohbe
Junior member
 
Join Date: March 22, 2009
Location: U.S.A.
Posts: 817
Degreasing Solvents:

I want to alumi-hyde something, and Brownells says to use a TCE degreaser.

Of course, they want you to buy theirs, but what else can I use as a substitute?

I was thinking of using Ether, I use that for degreasing engine parts. I've sprayed it on the sythetic stock I'm going to paint and it doesn't seem to affect it at all. I do know that it will eat through duracoat though. I used it to clean a 10|22 reciever and all the factory epoxy paint melted off .

My other idea was good old acetone. Brake cleaner doesn't get everything off.


Any suggestions or experiences?

Thanks.
essohbe is offline  
Old December 5, 2009, 03:49 PM   #2
brickeyee
Senior Member
 
Join Date: December 29, 2004
Posts: 3,351
The problem is that there are often contaminants in thinks like carb cleaner that can stay behind.

Brake cleaner is usually pretty oil free.

Denatured alcohol is normally ethyl alcohol denatured with methyl alcohol (though there are denaturing 'recipes' that even use gasoline).
It tends to be pretty clean.
brickeyee is offline  
Old December 5, 2009, 03:50 PM   #3
Pahoo
Senior Member
 
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
You really have to take care with this stuff but how about Carb & Choke cleaner. Take care as it will also remove paint and start to melt some plastic. They also make a Lawn mower cleaner that you spray one and let it sit awhile, then wash it off. I'll bet that one of the Gunk products will work. Some of the ones you mentioned, can be very harmful to breath so make sure you have some ventilation.




Be Safe !!!
Pahoo is offline  
Old December 5, 2009, 08:32 PM   #4
Dfariswheel
Senior Member
 
Join Date: May 4, 2001
Posts: 7,477
The better your prep, the better gun coatings work out.

I recommend multi-part cleaning.
Start out with a strong cleaner like Greased Lightning (Note that some of these cleaners WILL attack aluminum) and a tooth brush, followed by a hot water rinse.
Dry, then flush thoroughly with Acetone or Lacquer thinner.
Allow to dry again, then warm the metal with a hair dryer.
If there's any oils present the heat will cause it "blush" on the clean metal.
If so, flush again with the Acetone.

While its hard to get now after the EPA listed it as dangerous, Trichloroethane (Chloroethane) is one of the very best de-greasers, and is nominally non-inflammable. It will burn but you have to work at it.
Dfariswheel is offline  
Old December 6, 2009, 11:21 AM   #5
grumpa72
Senior Member
 
Join Date: April 5, 2009
Posts: 487
I use any of the non-chlorinated brake cleaners out there. Good solvent capabilities, no residue left over and a very cost effective cleaner. I can get it on sale for under $3 per can.
grumpa72 is offline  
Old December 6, 2009, 11:49 AM   #6
gyvel
Senior Member
 
Join Date: August 30, 2009
Location: Northern AZ
Posts: 7,172
Walmart "Tech" carb cleaner, $1.48 a can. Highly effective, but flammable.

DO NOT spray on plastics or your stock; It will take the finish off.
gyvel is offline  
Old December 6, 2009, 11:59 AM   #7
grumpa72
Senior Member
 
Join Date: April 5, 2009
Posts: 487
I have read that carb cleaners can leave a residue, thus the reason for brake cleaner. Is there any truth to the residue issue?
grumpa72 is offline  
Old December 6, 2009, 03:22 PM   #8
jimvac49
Member
 
Join Date: October 29, 2009
Location: Cape Coral, FL
Posts: 16
Yep, all those cleaners are good but you are right about some leaving a residue.
Back when Brownells first starting selling "Gun-Kote" (?) I did a few guns and parts. After the chemical cleaning, the finish didn't quite spray on as evenly as it should.
I found that after solvent cleaning, a good scrubbing in "hot" soap and water was the answer. The hotter the better as the water would evaporate from the hot metal.
My friend still has an old Norinco 1911 that still looks good.
jimvac49 is offline  
Old December 7, 2009, 04:22 AM   #9
gyvel
Senior Member
 
Join Date: August 30, 2009
Location: Northern AZ
Posts: 7,172
Walmart Tech doesn't leave a residue. It's usually the more expensive brands that leave residue.

I use Walmart Tech all the time for degreasing and get excellent results.
gyvel is offline  
Reply

Tags
alumi-hyde ii , alumihyde , degrease , degreasing , kittens

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:00 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.04336 seconds with 8 queries