|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
February 13, 2014, 10:32 AM | #1 |
Senior Member
Join Date: November 20, 2008
Posts: 11,132
|
Who sells fire blue grips screws?
Who makes/sells fire blue (high-polish bright blue) grip screws for 1911's, Hi-Powers, etc. Someone has to make these - I've seen them on custom guns. I've searched the internet and I'm coming up with nothing.
|
February 13, 2014, 02:33 PM | #2 |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,423
|
You can do it yourself, pretty cheaply.
Polish the screw heads. Evenly heat to straw yellow or dull cherry red (in dim light, not bright sun), depending on the color you want. And, drop into motor oil.
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
February 13, 2014, 04:09 PM | #3 |
Senior Member
Join Date: November 20, 2008
Posts: 11,132
|
I don't have a torch. I suppose I could buy one, but I hate to invest in a torch and a bunch of grip screws just to try this out. I know, I'm lazy - I was hoping there was somewhere that specialized in getting that shiny, bright fiery blue on small parts.
|
February 13, 2014, 05:27 PM | #4 |
Staff
Join Date: September 25, 2008
Location: CONUS
Posts: 18,457
|
Try Cylinder & Slide
|
February 13, 2014, 07:28 PM | #5 |
Senior Member
Join Date: April 7, 2006
Posts: 10,979
|
You don't need a torch. You can use a stove.
|
February 13, 2014, 08:19 PM | #6 |
Senior Member
Join Date: November 3, 2009
Location: Maryland
Posts: 526
|
Exactly. I did all fire-blue screws for a flintlock a few years ago using the gas burner on my kitchen stove. I basically polished the screws until I got the surface I wanted, held them with pliers in the flame (head farthest away) and let the color creep up the shaft of the screw. That way, I could see the progress and then remove the screw and drop it in oil as soon as it hit the color I wanted. Took 10 minutes to do a handful.
__________________
You only take one shot at a time - make it count. |
February 13, 2014, 09:19 PM | #7 |
Senior Member
Join Date: April 7, 2006
Posts: 10,979
|
You don't even need oil. You can use water.
If you are very careful, you don't need either. |
February 14, 2014, 08:29 AM | #8 |
Senior Member
Join Date: November 20, 2008
Posts: 11,132
|
Ok, you guys are making this sound too easy. I may have to give it a go.
|
February 14, 2014, 06:35 PM | #9 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
You can even do it on an electric stove (not one of the radiant heat ones though). With a standard burner, just hold the screw on the ring of a burner and wait until it is the color desired. Then quench in oil or water.
Jim |
February 15, 2014, 07:51 AM | #10 |
Senior Member
Join Date: August 30, 2009
Location: Northern AZ
Posts: 7,172
|
Just try practicing on a few nails first. Very cost-efficient practice.
|
February 15, 2014, 08:48 AM | #11 |
Junior Member
Join Date: January 16, 2013
Posts: 6
|
I'm with the DIY guys! But if that doesn't get you what you're looking for you might try Turnbull Restoration.
|
February 15, 2014, 08:57 AM | #12 |
Senior Member
Join Date: December 29, 2010
Location: Shoshoni Wyoming
Posts: 2,713
|
Oh heck....PM me.
If you send them to me I'll do them for you free. You pay postage both ways and we'll call it good. |
February 16, 2014, 08:46 AM | #13 |
Senior Member
Join Date: August 13, 2001
Location: central IL
Posts: 769
|
Dumb question. Is the temper affected?
|
February 16, 2014, 10:22 AM | #14 |
Senior Member
Join Date: December 29, 2010
Location: Shoshoni Wyoming
Posts: 2,713
|
Yes it is, but the 620 degree temp that turns the screw blue is the same temp you draw good spring steel at. So if the screw is mild steel (which most are) there is no heat treatment in the first place, so nothing is affected.
If the screw is made of a better grade of steel it will do nothing to affect them badly, and can possible make them better. |
Thread Tools | Search this Thread |
|
|