|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
February 15, 2002, 06:47 AM | #1 |
Senior Member
Join Date: December 11, 2000
Location: Phoenix, Arizona
Posts: 422
|
A-MERC brass - use it or lose it?
A friend just gave me a mixed lot of once fired 45 ACP brass containing a few hundred A-MERC casings.
I have heard folks saying they simply toss this stuff away. I have a lot of mixed brass that I re-use over and over for light plinking loads. I have noticed in the past that there were a few dozen of these A-MERC cases in there with the others. As a result, I have (unwittingly) reloaded these cases several times. Oddly, I have not experienced any problems. I will admit, because of some of the comments I have heard, I have been tossing stragglers as I notice them, just in case. (pun intended). Anyone have any specific horror stories they can relate or reasons I should toss this stuff outright? |
February 15, 2002, 07:42 AM | #2 |
Senior Member
Join Date: August 10, 2000
Location: WI
Posts: 1,395
|
It's thin, soft, and has loose primer pockets. trash it.
__________________
A plan is just a list of things that doesn't happen. |
February 15, 2002, 07:45 AM | #3 |
Senior Member
Join Date: January 26, 2002
Location: in a state of confusion and disbelief !
Posts: 726
|
ditto,ditto,ditto, offset primerholes, uneven size primerholes,ditto trash it!!!:barf:
__________________
N.R.A. Lifer and proud of it ! You can't argue with a .357 Mag. Well, you can try, but you'll end up bleeding an aweful lot. -GEORGE HILL 4-08-2002 My Coonan is Not For Sale please do not ask! |
February 15, 2002, 09:49 AM | #4 |
Senior Member
Join Date: August 13, 2001
Location: Montana
Posts: 489
|
Trash it...
__________________
http://stevespages.com/page8.htm |
February 15, 2002, 10:02 AM | #5 |
Senior Member
Join Date: January 13, 2001
Location: NC
Posts: 589
|
thin--Hell!!!!--the damn stuff is so thick that most lead bullets when seated will not chamber---another vote for chunking the mess..................Dick
|
February 15, 2002, 10:06 AM | #6 |
Senior Member
Join Date: December 9, 1999
Posts: 4,131
|
Agree with Dick...that stuff is WAY thick! You won't be able to chamber a single round using that crap. Don't jsut toss it, THROW it at that "friend."
__________________
Favor the X. Steve Smith NRA Life Member |
February 15, 2002, 10:30 AM | #7 |
Moderator in Memoriam
Join Date: August 28, 1999
Location: North Texas
Posts: 4,123
|
I've read a lot of varying opinions about it - - -
- - -But they were all of a mind on one point:
A-MERC brass is NOT WORTH THE TROUBLE! Sorry - - - Best, Johnny |
February 15, 2002, 10:41 AM | #8 |
Senior Member
Join Date: December 30, 2000
Posts: 699
|
Everything said here has been true. However, A-MERC brass is very good for turning into bullets for my 45-70. Always a silver lining.
|
February 15, 2002, 11:51 AM | #9 |
Senior Member
Join Date: April 9, 2000
Location: Lakeland, TN
Posts: 1,622
|
It is a sin that they use the name American on that crap.
__________________
"The key is to not pull the trigger but to squeeze it." Evil Emporer Zurg "You are entitled to your own opinion, but you are not entitled to your own facts." Unknown |
February 15, 2002, 12:51 PM | #10 |
Senior Member
Join Date: January 13, 2001
Location: NC
Posts: 589
|
if there is a way to make jacketed bullets for my 45-70 using 45 cases i'd like to know about it.......Tell me more.........Dick
|
February 15, 2002, 12:55 PM | #11 |
Senior Member
Join Date: March 19, 2000
Posts: 2,904
|
For the last 4 months the only FTF I experienced with my .45 ACP is A-MERC brass. I'm still picking it our of my collection.
__________________
"Given a choice between good intentions and human nature, I'll go with human nature every time."--Me, 2002. |
February 15, 2002, 02:49 PM | #12 |
Senior Member
Join Date: January 14, 2001
Location: Alexandria, VA
Posts: 203
|
Do I sense a "concensus" here ? ?
Why don't you guys just say what you mean out plain ?
Seriously, now: Consistently have problems with it. My experience is, I can't seat new primers. Clean it before you toss it !
__________________
An Armed Society, Is a Polite Society. |
February 15, 2002, 07:11 PM | #13 |
Senior Member
Join Date: September 23, 2001
Location: Central Alabama
Posts: 158
|
But there is a way!
Yes, A-MERC brass is terrible. It's much harder than other brands, and thicker as well.
You can still make usable cartridges from A-MERC brass if you do the following: Use a generous belling. The narrow mouth of the A-MERC brass will make this necessary for you to have any hope of seating a bullet. Then, after you crimp the round, run it through a Lee Carbide Factory Crimp Die. Something happens during the seating process that creates a bulge in the middle of the case. The Lee Carbide Factory Crimp Die will eliminate the bulge. I still prefer to toss it out, though. Many a time, I have seen a piece of A-MERC brass that has an off-center flash hole. I haven't bent a decapping pin yet, and don't intend to on a piece of A-MERC brass. |
February 15, 2002, 07:33 PM | #14 |
Senior Member
Join Date: August 8, 2001
Posts: 519
|
Why clean it first??
I just toss the stuff as far as i can
__________________
The Forty-Four spoke and it sent lead and smoke And seventeen inches of flame. -Marty Robbins JM |
February 15, 2002, 09:20 PM | #15 |
Member
Join Date: December 8, 2001
Location: Michigan
Posts: 31
|
You can use it for bullet setups on seating depth that you might then throw out.
|
February 16, 2002, 03:20 AM | #16 |
Senior Member
Join Date: December 11, 2000
Location: Phoenix, Arizona
Posts: 422
|
Folks,
Have to admit, the responses are exactly what I had hoped for. Some of the suggested uses were demonstrative of the level of insight and experience here. In any case, I will be throwing a few hundred rounds of A-MERC brass (highly polished - too late) into the trash tomorrow. Not even going to waste my time trying to trifle with something that positively sounds like more trouble than it is worth. Lee Carbide Factory Crimp Die. In the quest for better quality ammunition, you guys continue to mention this little devil. Crimping is the only process in reloading for pistol that always makes me feel uneasy. It just seems like "government" or "German" torque and such an imprecise science. (I'm half German and have plenty of experience). I "think" I'm doing it right, and with about 15,000 45 ACP rounds downrange, I'd hope I'm at least close. I'm currently using the Dillon four die set on a 550 Dillon. You guys keep recommending this Lee crimping die as a REPLACEMENT for the Dillon crimping die? Will it work on a 550 tool head? One of the posters said it's a no-go except on the 650 Dillon. I've seen the other threads, but should I really swap it out (if it is possible)? Kind of like putting Ford parts on a Chevy or vice versa. Real benefits over the Dillon crimping die? Is this in all pistol calibers, or specifically 45 ACP? I'd be interested in .38/.357, 9mm and 45 ACP and perhaps .40 and 10mm (eventually). Thanks! |
February 16, 2002, 07:51 AM | #17 |
Member
Join Date: December 8, 2001
Location: Michigan
Posts: 31
|
One benefit of the FCD is that seating with one die and crimping with another die can be more precise. But you need two toolhead stations in the press.
Also sometimes even without Amerc brass, the case has a slight bulge. Post sizing the straight walls after seating and crimping makes the bullet more perfect. Especially for competition instead of just plinking or just trying to make noise with a gun, it helps consistency. After running through a progressive press, then I run them one at a time through a single stage press. |
February 16, 2002, 08:27 AM | #18 |
Senior Member
Join Date: January 13, 2001
Location: NC
Posts: 589
|
a buddy was bitching about amerc the other day and he said he just ran it through the sizer again with the bullet seated.....i'd tried this years ago with other brass and bullets but just to make him feel better i said we'd try it again......sure enough the result was the same as i remembered years ago......after running it through the sizer you could slide the lead bullet right out of the case.........damn--i think i'll just do this to all my bullets that need pulling and do away with my inertia bullet puller--ha ha.....Dick
|
February 16, 2002, 09:05 AM | #19 |
Senior Member
Join Date: January 8, 2001
Location: Forestburg, Montague Cnty, TX
Posts: 12,717
|
Some of the guys I shoot with reload. Often when they have a case failure that I see at the range, it is an A-MERC case. Apparently, a lot of them never make it to the range, splitting during reloading.
So other than being too thin, too thick, soft metal, loose primer pockets, and cases failing, you should not have any problems.
__________________
"If you look through your scope and see your shoe, aim higher." -- said to me by my 11 year old daughter before going out for hogs 8/13/2011 My Hunting Videos https://www.youtube.com/user/HornHillRange |
February 18, 2002, 04:49 AM | #20 |
Senior Member
Join Date: December 5, 1999
Location: Seattle, Washington, USA
Posts: 1,686
|
TRASH IT
__________________
The Seattle SharpShooter Reloaded .223 Rem, 9mm, 40SW, 357 SIG, 10mm, 44 Mag, 45 ACP Today? |
February 18, 2002, 04:15 PM | #21 |
Senior Member
Join Date: January 14, 2000
Location: Southern California
Posts: 1,089
|
At least one unlucky Glock shooter will probably not use A-Merc again..
http://www.frontsight.com/safety.htm |
February 20, 2002, 12:33 AM | #22 |
Member
Join Date: February 16, 2002
Location: Wichita Falls,TX.
Posts: 49
|
A-Merc brass
Well, it is thick and kinda soft, but I have some I have loaded 6-7 times, and hasn't failed me so far...yet the ammo loaded from them is "OK"
|
February 20, 2002, 06:12 PM | #23 |
Member
Join Date: January 13, 2001
Location: Florida
Posts: 29
|
Off topic but...
KP95DAO, if you've got a neat trick for turning 45 ACP brass into 45-70 bullet jackets then give up the gouge!! |
February 20, 2002, 07:02 PM | #24 |
Member
Join Date: February 16, 2002
Location: Wichita Falls,TX.
Posts: 49
|
No kidding, do you have a Corbin bullet swadger, or do you know some trick to do it without such expensive equipment?
|
February 21, 2002, 08:38 AM | #25 |
Senior Member
Join Date: January 13, 2001
Location: NC
Posts: 589
|
i got an email from him and he says he's going to post it sometime soon.....waiting with baited breath.....Dick
or maybe it is breath that smells like bait........ |
|
|