|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
May 10, 2001, 06:28 PM | #1 |
Senior Member
Join Date: March 30, 2000
Location: Indiana
Posts: 607
|
How many times can you reload your rifle brass? As in 30-06
|
May 10, 2001, 07:14 PM | #2 |
Senior Member
Join Date: April 17, 2001
Location: Farnham, Va
Posts: 2,183
|
It'd be great if there was a set number of times, or even an average number, for that matter. I've always pondered that one that one myself.
I weed out most of my older shell casings by case lengths. I trim my shells every time, regardless of measured length. As soon as casings won't make it to my personal minimum length of .010 under the book's minimum length, I load it one last time, shoot it, and it gets chucked the next time around. I can't even give a good guesstimate, because each casing manufacturer has different grades of casings. Some wait until a failure of some sorts, whether it be extreme bulging, rips, or explosion. I've never had enough money lying around to buy a new gun over a 5 cent bullet, so I prefer a more conservative method. That'd be a good idea for website - a database of different casings and the average life expency posted by readers. hmmmmm...... |
May 10, 2001, 07:54 PM | #3 |
Senior Member
Join Date: November 28, 1999
Location: California
Posts: 3,925
|
It all depends on the caliber and the number of times you gave reladed the cases.
|
May 10, 2001, 08:06 PM | #4 |
Senior Member
Join Date: February 19, 2001
Location: Iowa
Posts: 141
|
PD shooter I think a lot of it depends on your chamber, and how well the case fits it. Have a TC. in 7TCU that eats a case every 10 to 15 loadings, but I have to size it quite a bit. also have a XP in 7IHMSA, or had, used Fed 308 match brass, that had to be bumped back .010 and necked down. That made the necks too thick so turned them to .001 under chamber size. Shot 3000 rounds a year in it till the barrel went ( about 5 years ) and never lost a case, Though the primer pockets did get a little lose. Of corse they were never sized, didn,t need it.
|
May 10, 2001, 11:55 PM | #5 |
Senior Member
Join Date: November 20, 2000
Location: Ohio
Posts: 3,968
|
It also depends on how hot you are loading, what caliber you are loading, and whether you are full length resizing or neck sizing.
__________________
You know the rest. In the books you have read How the British Regulars fired and fled, How the farmers gave them ball for ball, From behind each fence and farmyard wall, Chasing the redcoats down the lane, Then crossing the fields to emerge again Under the trees at the turn of the road, And only pausing to fire and load. |
May 11, 2001, 07:27 AM | #6 |
Senior Member
Join Date: October 7, 2000
Location: In the Lost State of Franklin
Posts: 482
|
Determining factor
The shortest case life will occur with semi-autos. These must be sized smaller than bolt guns because of the lack of caming action to seat an oversized case in the chamber. The most likely problem to occur is case head seperation. There ARE, however, ways to reduce the problem.
First, resize the MINIMUM amount necessary to reliably chamber. Now, obtain an old dental pick from your dentist (or fashion a tool from a large paper clip) and use it to feel for a slight groove inside the case, just above the head (as far down in the case as you can get.). You'll soon develop a "feel" for it. By culling cases with grooves, you've eliminated the most likely (and dangerous) method of failure. Now, you're down to split necks (which can be delayed by annealing) or body splits. Neither of which is a catastrophic failure. Yr. Obt. Svnt.
__________________
Your Most Humble & Obedient Servant Fred J. Drumheller NRA Life NRA Golden Eagle |
Thread Tools | Search this Thread |
|
|