|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
June 16, 2012, 08:20 AM | #1 |
Senior Member
Join Date: April 29, 2012
Location: East Texas
Posts: 105
|
45 ACP Reloading Problem
Hey guys, you all have been a great resource for this new reloader. I've been cutting my teeth on 9mm Lugar and feel pretty comfortable with that round, so I set up my RCBS die to reload some 45 ACP. I used my Winchester brass that was once fired, cleaned, de-caped and resized. The instructions on the carbide die set say the case mouth should be expanded (belled) just enough to accept the bullet base- no more!
I followed instructions for the bullet seating and the got the OAL perfect. Then I pulled the bullet because I was just using a dummy round to get the dies set up. This is when I noticed the bullet had a "ring" around it. Looks like from the base to about .244" up the side of the bullet is compressed. Trying to attach a picture to illustrate the issue that I'm having. Any help is appreciated. Reef |
June 16, 2012, 08:41 AM | #2 |
Senior Member
Join Date: October 24, 2008
Location: GATOR COUNTRY HA HA HA!
Posts: 721
|
Are you using a Lee FCD (Factory Crimp Die) ?? If so Back off on the crimp JMO ; )
Y/D
__________________
There's a GATOR in the bushes & She's Callin my name >Molly Hatchett< |
June 16, 2012, 09:20 AM | #3 |
Senior Member
Join Date: August 7, 2010
Location: Northern, UT
Posts: 1,162
|
+1 on back off the crimp. You only need enough to knock off the bell and to give an ever so slight taper. .45 acp doesn't need much in the way of crimping.
Also, Plated bullets are less tolerant of that sort of thing than other bullet types.
__________________
Cheers, Greg “At the core of liberalism is the spoiled child – miserable, as all spoiled children are, unsatisfied, demanding, ill-disciplined, despotic and useless. Liberalism is a philosophy of sniveling brats.” — P.J. O’Rourke |
June 16, 2012, 10:05 AM | #4 |
Senior Member
Join Date: June 6, 1999
Location: El Paso, TX
Posts: 1,021
|
That doesn't look like anything a Lee FCD would do, I think you have your seating die screwed in too far as some are designed to crimp if they are screwed in beyond a certain point.
I would remove your seating die and raise a shell that has been through the expander die all the way up in your press. Then start lowering your seating die onto the shell until it contacts it and stops. Lower your lock ring down to the press, lower the shell and then give the die about a quarter turn to tighten it down. After that adjust overall length using the plug at the top of the die. For something soft shooting like a 45acp the two goals of the seating die are to get the correct OAL and remove any bell from the expander. It only needs enough "crimp" to straighten out the neck to ensure proper feeding. If you need more crimp beyond a quarter turn after contact do it about another quarter turn at a time. Remember this will shorten your OAL so make sure to correct it once you are done. For a seating die the difference between just enough and way too much is only a full turn or so.
__________________
New gun, same ol' shot. |
June 16, 2012, 10:09 AM | #5 |
Senior Member
Join Date: April 29, 2012
Location: East Texas
Posts: 105
|
Only using RCBS.
|
June 16, 2012, 10:23 AM | #6 |
Senior Member
Join Date: November 9, 2005
Location: Ohio, Appalachia's foothills.
Posts: 3,779
|
The word crimp is deceiving when it comes to 45ACP.
You just want to remove the flare. Sent from Tapatalk 2. |
June 16, 2012, 10:29 AM | #7 |
Senior Member
Join Date: June 30, 2009
Location: dallas
Posts: 773
|
Adam is right, you need to back off the seating die. It should be fairly obvious when you are at the end of you're stroke. You should feel the bullet sliding into the case but right near the end you will feel more tension. You can back out the die until the entire stroke feels the same. At that point you aren't crimping at all, which is okay for a lot of rounds. Your choice if you want a slight crimp, just screw the die back in a little. I don't crimp my 45 acp and do 9mm with and without, can't really tell the difference shooting wise.
|
June 16, 2012, 10:29 AM | #8 |
Senior Member
Join Date: February 14, 2008
Location: Kansas
Posts: 753
|
Are you sure you dies are for tapered crimp and not roll crimp ?
You should have a tapered crimp that ranges from .469" to .471" |
June 16, 2012, 10:36 AM | #9 |
Senior Member
Join Date: May 20, 2006
Posts: 925
|
When i first started I would back off the crimp and only seat, do a batch of 100 or so, then back off the seat and lower the crimp a little at a time till i just flattened the flare. I would then drop every tenth one into a barrel from my disassembled pistol to see that it chambered correctly. this adds a step but for me it helped me understand the difference of seating and crimping. good luck.
|
June 16, 2012, 10:54 AM | #10 |
Senior Member
Join Date: April 29, 2012
Location: East Texas
Posts: 105
|
Many Thanks, again
Thank you all. I did exactly what Adam said and it fixed my problem. I'm so new at this I thought the deformation of the bullet was caused by not enough flare from the expander die and the bullet being "squeezed" into the case. I didn't realize crimping could do that to the bullet.
Thank you all very much for the help. Reef |
June 16, 2012, 11:01 AM | #11 |
Senior Member
Join Date: April 18, 2000
Location: Metairie, Louisiana
Posts: 890
|
I've loaded thousands of .45 ACP with RCBS dies. As stated, you have the seating die screwed down too far and are over-crimping. Follow Adamantium's instruction for setting your seating/crimping die and you'll be good to go. All you need is to straighten out the flair and put a "little" pressure on the bullet.
__________________
Guns are not dangerous! People are! RKBA! |
June 16, 2012, 03:32 PM | #12 |
Senior Member
Join Date: September 28, 2008
Posts: 10,442
|
Also be aware that the mouth of the case is used to "headspace" the round.
The thickness of the front of the case, the part that surrounds the bullet, is meant to contact the front of the chamber in the barrel, in order to properly locate the cartridge in the chamber. Too much crimp can mess that up, by allowing the cartridge to move too far forward. Proper headspace is very important for many reasons. If in doubt how much crimp is correct, just compare your loaded rounds with a factory one.
__________________
Walt Kelly, alias Pogo, sez: “Don't take life so serious, son, it ain't nohow permanent.” |
June 16, 2012, 04:21 PM | #13 |
Senior Member
Join Date: August 23, 2011
Location: Trinity, Texas
Posts: 636
|
If I'm not mistaken .... the RCBS three die set seating die will provide a roll or taper crimp. Depending on the die adjustment.
__________________
David Bachelder Trinity, Texas I load, 9mm Luger, 38 and 40 S&W, 38 Special, 357Magnum, 45ACP, 45 Colt, 223, 300 AAC, 243 and 30-06 |
June 16, 2012, 04:30 PM | #14 |
Senior Member
Join Date: June 6, 1999
Location: El Paso, TX
Posts: 1,021
|
Thats a smart way to do it. All you would need is a seperate shell holder and you could reload both 45acp and 45 auto rim.
__________________
New gun, same ol' shot. |
|
|