The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old March 15, 2002, 07:53 PM   #1
pvanosta
Member
 
Join Date: December 19, 2001
Location: Long Beach, CA
Posts: 65
Cut-to-measure foam in case - look...

I got this $26.00 tool case from Lowes. It's a nice aluminum case with a foam bottom and a Compartmentalized tool flap behind the top foam layer inside the lid.
The foam in the bottom half was not very solid, so I went looking for a replacement.
I found
www.foamsweetfoam.com
They cut me two pieces the size of the case, one 1.75 inches think and one .75 inches thick.
I put the 1.75 inch piece down and then laid my guns out on the thinner piece. After outlining everything, I cut the pieces out with an electric carving knife.

The result is still a bit rough, but I have spare pieces of foam to work with and it's still a lot better than what it was. I now have a decent transport/presentation case for my little friends for a total cost of $40 or so...
Attached Images
File Type: jpg case4-2.jpg (81.2 KB, 177 views)
pvanosta is offline  
Old March 15, 2002, 08:27 PM   #2
NC-VT
Member
 
Join Date: February 4, 2002
Location: Central NC
Posts: 44
Looks good. I really like the look. I wish I woulda seen this a month ago. I just paid 60 bucks for one, and would rather have one more innocent looking, like this.
NC-VT is offline  
Old March 16, 2002, 12:27 AM   #3
laynlow
Member
 
Join Date: February 27, 2002
Location: OK
Posts: 86
That case looks great! Just for future ref., alot of Army / Navy Surplus stores sell foam too.
laynlow is offline  
Old March 17, 2002, 12:03 AM   #4
HKCowboy
Member
 
Join Date: December 2, 2001
Posts: 15
the case comes with it's own foam. the bottom is the "pick and pluck" type that you can trace and cut.
Attached Images
File Type: jpg dscn0008.jpg (63.9 KB, 102 views)
HKCowboy is offline  
Old March 17, 2002, 09:09 PM   #5
adk
Senior Member
 
Join Date: January 27, 2002
Location: Kern County mountains, Cal
Posts: 391
An easy way to do it is to get the lid foam and bottom foam pieces cut for the case with thicknesses that will leave a closed space of about 1/2" to 3/4". This will squeeze your guns and will squeeze 1"-thick pieces of foam in with the guns.

Cut a bunch of shapes and sizes from the 1" foam that you just lay in the case to put walls between the guns, and between the guns and the walls of the case. Just loose pieces. You put your guns in and arrange the foam parts accordingly. Really fast and flexible. The lid foam squeeze holds them in place. One case works for any guns.

I use 1.6 lb. ELE. It's strong enough to hold heavy guns apart. Charcoal color. I cut it on a little Sears bandsaw. Easy and neat method. No glue. Or, you can glue the pieces in place too. Easier than trying to cut exact gun shapes. Be sure to check how the case is made. Some of them have shells that can pop out from the squeeze pressure. Most briefcases are like this. adk
adk is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07761 seconds with 10 queries