The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Competition Shooting

Reply
 
Thread Tools
Old February 8, 2002, 02:31 AM   #1
Skunkabilly
Senior Member
 
Join Date: December 1, 2001
Location: Land of stinky cabbage and potable rubbing alcohol
Posts: 2,132
Berettas in IPSC

Anyone know if a Beretta Elite II with:

Trigger job
Novak rear & Trijicon front
Stainless Steel Guide Rod
Magazine rubber basepads

will be legal in Production class?
__________________
Skunky's World of Mud and Guts and Barbecue Sauce: www.skunkabilly.com
"Stupid American! There's no bloody sales tax for tea in Hong Kong. Didn't you start a war over a tea tax?" -- Hong Kong tea merchant
Skunkabilly is offline  
Old February 8, 2002, 07:06 AM   #2
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,242
WOULD BE AT OUR CLUB

Go to www.uspsa.org and check the rules; I 'think' you're A-okay, but what the h do I know?

But you would be in Production class at our club.........

FY33102
DVC
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old February 8, 2002, 08:52 AM   #3
eerw
Senior Member
 
Join Date: March 18, 2001
Posts: 395
Yup..should be no problem...

The guide rod, trigger job are internal..the sights are specifically allowed and the basepads are a factory item with the Elite II.

Have fun..
eerw is offline  
Old February 8, 2002, 12:59 PM   #4
Skunkabilly
Senior Member
 
Join Date: December 1, 2001
Location: Land of stinky cabbage and potable rubbing alcohol
Posts: 2,132
The stock Elite II comes with a plastic guide rod. IRC, some of the older Berettas have SS guiderods. This is the thing I'm not sure about, but I think it IS a factory Beretta item.
__________________
Skunky's World of Mud and Guts and Barbecue Sauce: www.skunkabilly.com
"Stupid American! There's no bloody sales tax for tea in Hong Kong. Didn't you start a war over a tea tax?" -- Hong Kong tea merchant
Skunkabilly is offline  
Old February 8, 2002, 03:00 PM   #5
Ricky T
Senior Member
 
Join Date: July 19, 1999
Location: ATL, GA
Posts: 197
Yes. There was a shooter that shot in the GA IPSC 2001 State Match that used a Beretta E2 in Production. He came in second place.
__________________
"Less yacking and more cacking" SDH
Ricky T is offline  
Old February 8, 2002, 03:18 PM   #6
Skunkabilly
Senior Member
 
Join Date: December 1, 2001
Location: Land of stinky cabbage and potable rubbing alcohol
Posts: 2,132
I guess my question is, if the SS guide rod is a factory (i.e. Beretta manufactured) item, but not part of the gun and I have to get it through another source (i.e. Langdon Tactical), will I be Production legal?
__________________
Skunky's World of Mud and Guts and Barbecue Sauce: www.skunkabilly.com
"Stupid American! There's no bloody sales tax for tea in Hong Kong. Didn't you start a war over a tea tax?" -- Hong Kong tea merchant
Skunkabilly is offline  
Old February 11, 2002, 04:06 PM   #7
jhisaac
Senior Member
 
Join Date: December 1, 2000
Location: Newberg, Or
Posts: 144
I'm going to weigh in with a contrary opinion.

I don't think the guide-rod is OK. If you got a plastic rod, then you need to shoot a plastic rod. I know it's a production part, but not in YOUR gun. Replacing the guide rod was not covered in the list of allowed mods.

"g. Action work to enhance reliability (throating, trigger work, etc.) is allowed." I know there is an unknown amount of room there in the "etc.", but that's what I think.

Also, If the base pads on the magazines are add-on, then those aren't kosher either. There was a BIG discussion about magazine lengh on the IPSC mail list and the opinion of John Amidon, chief RO or something like that is that magazines should be of the same overall specs as factory mags. Therefore, if the rubber pads make it longer, then it is not OK. Now, I will be the first one to admit that the rules do not support that position well. But that was the intent.

Jhisaac
jhisaac is offline  
Old February 12, 2002, 08:56 AM   #8
kbear38S
Senior Member
 
Join Date: September 27, 2000
Posts: 154
A steel guide rod would be allowed as it's internal. What would disallow it is the following clause:


USPSA 14th Editition Rule Book - Pg. 91
Appendix E US Divisions

Maximum weight, Yes, 2 oz. over factory.

I think, but am not sure, the answer to this was published in Front Sight when somebody asked about replacing the plastic guide rod in a Glock with a steel part.

Basepad bumpers would be legal if they are used on the stock mags included with the gun. If not, they aren't, even if they are Beretta parts.
kbear38S is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:22 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07151 seconds with 9 queries