The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old November 6, 2001, 02:24 PM   #1
Boo586
Member
 
Join Date: May 15, 2001
Location: Indiana
Posts: 85
Neck Sizing .357 magnum cases

Just got a good pair of calipers for my birthday, thanks to my father-in-law. I was just spending my lunch at home measuring some resized cases and some unresized fired cases. The resized cases measure 0.372 inches in diameter. Some .38 special cases measure 0.375 inches and some once fired .357 magnum brass measures 0.381. The chambers of my revolver measure about 0.382 inches to best of my ability. After I mesured these I chambered each one of the cases one at a time to see how the cases fit in the chambers. The resized case and the .38 special case moved around in the chamber a lot, while the once fired magnum brass fit snug but did not have to be forced into the chambers.

Using the unsized cases should keep my pressures lower and be easier on my gun with my hunting loads. I am also thinking that the snug fit of the cases in the chaber will help to align the bullet with the barrel and increase the gun's accuracy. For the few cases that have to be pushed into the chamber I am going to try and resize the cases by rolling the cases between two metal plates to remove any slight bulges that might be present. Then I am just going to neck size the cases where they hold the bullet and then crimp heavily.

Has anybody done this and is my thinking along the correct lines, or am I way off base?

Thanks for the Help!!

Boo586
Boo586 is offline  
Old November 6, 2001, 02:32 PM   #2
Jeeper
Senior Member
 
Join Date: November 1, 2001
Location: Gilbert, AZ
Posts: 776
I am not sure how much of a true "neck size" you can do with pistol dies. I have never tried it or thought to. Since the bottom of the brass is usuall the largest area your brass still might be a little to tight. I have never had any accuracy problems by full length sizing brass and having a loose cylinder. I have a 357 FA that I use for pistol silhouette at 200 yards and it has always performed well using full length sizing. You could always try it and see what happens. You could also try full lengh sizing and see how they compare accuracy wise. I personally hate havig to shove ammo into a revolver. I prefer an easy fit.
Jeeper is offline  
Old November 6, 2001, 02:39 PM   #3
Ben Shepherd
Senior Member
 
Join Date: August 11, 2001
Location: Utah
Posts: 1,462
check the thread on magnum primers. Read Steve Smiths comments.
__________________
From my cold dead hands.........

NRA certified rifle, pistol and shotgun instructor.
Hunter education instructor
Ben Shepherd is offline  
Old November 6, 2001, 06:48 PM   #4
Bogie
Senior Member
 
Join Date: June 5, 2000
Location: Job hunting on the road...
Posts: 3,827
You'll see a bigger increase in accuracy if you get a good tight crimp... I wouldn't mess with "roll sizing" pistol ammo.
__________________
Job hunting, but helping a friend out at www.vikingmachineusa.com - and learning the finer aspects of becoming a precision machinist.

And making the world's greatest bottle openers!
Bogie is offline  
Old December 19, 2001, 06:31 PM   #5
canuck2
Junior Member
 
Join Date: December 19, 2001
Posts: 9
Hi, I don't have pistol experience but my feeling from working at HIGH pressures with 6PPC benchrest is that sized cases will give you lower pressure not higher, because the brass has some room to give, absorbing some energy while expanding. At least With 6PPC and I suspect in general this has more effect than that of a very small difference in cartridge volume which I suspect you are considering.
Regards, Ed
canuck2 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07394 seconds with 9 queries