The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 17, 2001, 05:50 PM   #1
RugerSAfan
Member
 
Join Date: April 21, 2001
Posts: 35
Reload cost - relief

Was at the local sporting goods store to price non-equipment components, to help justify purchase of press.

Pulled out the Winchester Components catalog to determine amount of 231 for each .45 colt load.

1 lb 231 = 16.99

100 primers cci = 1.69

500 200 gr swc
Meister bullets = 25.99

Talked to the old boy behind the counter; asked him how
many grains per pound; he looked at the bottle and said
454. Youzers! I priced out the of powder per cartridge, and
it was 21 cents each!

Well, did a search on this board, and found out there are 7,000 grains per lb. Big difference! Big relief!
RugerSAfan is offline  
Old December 17, 2001, 06:09 PM   #2
Keith J
Senior Member
 
Join Date: December 15, 2000
Posts: 469
Again, someone selling the stuff who know less that required to sell it. I guess 99% of my reloading questions were answered by my father before the age of 12. I knew it was 437.5 grains per ounce or 7000 per pound.

I also knew it was about 454 grams per pound but since no manual ever listed weights in grams, it was useless knowledge.
Keith J is offline  
Old December 17, 2001, 06:49 PM   #3
dick w. holliday
Senior Member
 
Join Date: January 13, 2001
Location: NC
Posts: 589
one of my favorite numbers is 56,000----------the number of grains in an 8 pound can------if your loading 5 grains or so of 231 in a shell like 38 or 44 or 45 your getting 12,000 + loads per can.....after i threw out all those empty 231 cans--i wondered where all that powder went...hope it don't f#ck up the ozone layer................Dick
dick w. holliday is offline  
Old December 17, 2001, 07:05 PM   #4
LilJoe
Senior Member
 
Join Date: March 2, 2001
Location: North Eastern Ohio
Posts: 185
RugerSAFan, what part of the world are you in? Powder and primer prices seem ok but the lead seems a little on the high side. If memory severs right I think you aren't far from a bullet manu. But then again they say the memory is the first thing to go..
LilJoe is offline  
Old December 17, 2001, 08:00 PM   #5
RugerSAfan
Member
 
Join Date: April 21, 2001
Posts: 35
Is there a bullet manuf. in West Michigan
RugerSAfan is offline  
Old December 17, 2001, 08:52 PM   #6
Redneck2
Senior Member
 
Join Date: April 24, 2000
Location: Northern Indiana
Posts: 519
I think if you do the math...

He had ounces instead of pounds...437 per ounce....7000 per pound.

I'd shop a little harder for bullets. I can get Shooters Choice (they don't lead) for $20.50 in Merrillville, IN. Very clean to shoot. If you get to this area I'd check it out. If you need directions e-mail.

If you want to get by cheaper, try around 10 grains of Unique under a 250 grain (for RUGERS). IIRC gives maybe 1,100 fps. Mild load.

For a really in-depth disussion, check realguns.com...he has an extensive cost break-down of different powders and velocities.

Using 10 grains of a fast powder gave close to as good of performance as 24 grains of W296 and was considerably cheaper. IIRC his "top pick" was X-700. Obviously you can get 2 1/2 times as many loads with 10 grains as 25 grains. This will change the powder cost per round from maybe 2.5 cents to 6.8 cents.

Last edited by Redneck2; December 18, 2001 at 06:28 AM.
Redneck2 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:08 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07781 seconds with 9 queries