The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 27, 2001, 06:20 PM   #1
Phil in Seattle
Member
 
Join Date: January 29, 2000
Posts: 97
I have a new 444 Marlin rifle that I will be loading for (Have you seen the cost of factory ammuntion for this cartridge!). and I don't have any personal experience with powders suitable for this cartridge.

I like the same thing in my powders that everyone else does, constancy, clean burning, and meters nicely. Among the following powders does anyone have any input?

IMR4198
H4198
RL-7
VIHT N-130
H335
Phil in Seattle is offline  
Old May 27, 2001, 07:06 PM   #2
444
Senior Member
 
Join Date: November 20, 2000
Location: Ohio
Posts: 3,727
I think you will find that for serious loads, H335 is THE powder. Welcome to the club. If you start playing around with the .444 you will see a very versitile caliber. Right now I am playing around with "silent" loads using a 300 grain cast bullet and about 4 grains of Bullseye powder. No noise, no recoil and one hole accuracy at 25 yards. My "go to" load for the .444 is H335 and a 300 grain Hornady JSP at about 2200 fps. I was going to mention the charge but I see that it is over max for several of the manuals so I will leave that up to you. I am shooting the Marlin and at 100 yards, it is hands down the most accurate rifle I own. And I have never had a load that wasnt' accurate. My next project is to load shotshells for the .444 approximating a .410 bore shotgun. Check out some of the articles by Paco Kelly at http://www.sixgunner.com on the .444
__________________
You know the rest. In the books you have read
How the British Regulars fired and fled,
How the farmers gave them ball for ball,
From behind each fence and farmyard wall,
Chasing the redcoats down the lane,
Then crossing the fields to emerge again
Under the trees at the turn of the road,
And only pausing to fire and load.
444 is offline  
Old June 10, 2001, 04:16 PM   #3
dundee
Senior Member
 
Join Date: December 6, 1998
Location: mytown,mi,usa
Posts: 162
Beg to Pardon but I realllly don't like to use h335 powder in the 444. The flash and boom are very impressive, more so than I like. THE powder for the 444 is 4198, in either IMR or Hodgdon flavor. Second choice is 3031.

Until I got my 44 lever gun I was using 20gr of 2400 under a 255 cast lead bullet for a moderate 100/200 yd plinking load in the 444.
dundee is offline  
Old June 10, 2001, 09:52 PM   #4
Phil in Seattle
Member
 
Join Date: January 29, 2000
Posts: 97
I got my hands on some H335 yesterday and I'll be making some loads up this week and trying them out on Saturday.
I'll see if I can get some 4198 this week and I'll compare the two.

I have to admit though that the big flash and boom sound appealing to me althouhg it might be too much from this short barrel.
Phil in Seattle is offline  
Old June 10, 2001, 10:59 PM   #5
Kernel
Senior Member
 
Join Date: November 21, 1999
Location: Madison, WI.... "78 Square Miles Surrounded by Reality"
Posts: 922
My Powley Computer agrees with dundee. It says powders in the speed range of 4198 are THE ones to use with 240 and 300 gr bullets. Also try your Reloader 7, it's only a tad slower and I've had very good results with it in the similar .375 Winchester. -- Kernel
Kernel is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:03 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06393 seconds with 9 queries