The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old August 4, 2014, 04:52 PM   #1
NHSHOOTER
Senior Member
 
Join Date: November 26, 2012
Location: Concord NH
Posts: 273
cleaning rods

While looking for a new cleaning rod I have come across, brass, steel and aluminum..I always thought brass was the best because it was softer than steel. I am sure there are more seasoned veterans out there that know more than me, so I am asking, Which is best?
NHSHOOTER is offline  
Old August 4, 2014, 05:05 PM   #2
Mosin-Marauder
Senior Member
 
Join Date: April 18, 2014
Location: North Carolina
Posts: 1,111
There are people that say particles can get "trapped" in anything other than steel and can act as an abrasive. Personally I see this as untrue.After working with steel a long time, I can tell you that an "abrasive" is a lot less harmful than full steel-on-steal contact. There are also some people that say steel rods don't harm bores, again, I find this untrue. Over a long period of cleaning, a steel rod will wear away more than a softer metal or nylon. I'd go with a brass or aluminum or Dewey coated rod. A lot less likely to do damage to your rifle. And bore snakes leave crud in the bore.
__________________
Proud owner of two pieces of history!
K-31, made in 1949 all original, beech stock.
Mosin-Nagant M91/30, 1941 all original.
Mosin-Marauder is offline  
Old August 4, 2014, 05:45 PM   #3
Bart B.
Senior Member
 
Join Date: February 15, 2009
Posts: 4,900
Dewey coated one-piece rods are popular with folks producing best results in competition. So's a solid stainless steel rod. None of 'em use soft metal rods such as aluminum or brass. But use a cleaning rod guide in the receiver to keep them aligned with the bore and not lap away the rifling at its origin. Use a rod diameter as big as possible that fits your bore easily; they're stiffer and easier to use.

Best wishes using what you feel most comfortable with.
__________________
US Navy Distinguished Marksman Badge 153
Former US Navy & Palma Rifle Team Member
NRA High Power Master & Long Range High Master
NRA Smallbore Prone Master
Bart B. is offline  
Old August 4, 2014, 06:26 PM   #4
Lucas McCain
Senior Member
 
Join Date: March 7, 2013
Location: Callaway, MN
Posts: 200
Bart nailed it, he was typing when I was also.

Take a look at the on-line offerings of Sinclair International . They only handle quality cleaning rods. You don't want a jointed rod, definitely not an aluminum or brass rod. The biggest problem with them is that they aren't stiff enough to keep from bending when being run down the bore with a patch and contacting the rifling. IMHO there is nothing wrong with a good quality steel rod with a jewelry finish, that is made out of spring steel that don't bend. They have the proper finish and work excellent.
The other half of proper cleaning rod use is a bore guide, one that fits into the chamber of the rifle and protects the throat in front of the chamber from the cleaning rod rubbing on it. For those rifles that are cleaned from the muzzle you need a bore guide to protect the crown on the rifle from contacting the riflings at the crown. Cleaning from the muzzle is the only way to clean some rifles. But it is the least desirable to clean a rifle. Clean it from the breech if at all possible.
Also you need the proper sized swabs to wipe out the chambers and throat when your done cleaning the barrel. Some of the stuff you scrub out of the barrel can get in the chancre and even the locking lug area. Locking lugs areas (both bolt and breech)are the most neglect items when guns are cleaned. It don't get cleaned then they blame the ammo when it don't close properly.
I also only use brushes and swabs that have bronze twists that are round on the end. To many brushes and swabs sold at LGS have steel twists that are cut and have sharp ends. Something like that is not what I want shoved down any of my gun barrels. Way to much potential for damage to occur to the rifling.

I mentioned Sinclair for cleaning rods. They handle Pro-Shot, Montana-Extreme, Dewey and some others. Their products are high quality and they do cost a fair amount of $.
We pay a good price for a quality rifle, probably put a quality piece of glass to achieve the best accuracy possible from the gun. Does it make any sense at all to go the cheap route when it comes to cleaning equipment. Using proper cleaning equipment and procedures has more effect on long term accuracy of the rifle, than anything else.
__________________
If you have time to do it twice, then you have time to do it once right and put your name on it
Lucas McCain is offline  
Old August 4, 2014, 07:27 PM   #5
JWT
Senior Member
 
Join Date: March 16, 2007
Location: Tucson, AZ
Posts: 3,151
I have gone to all Tipton or Dewey coated one piece rods. Very satisfied with them in all respects.
JWT is offline  
Old August 5, 2014, 06:42 AM   #6
Clark
Senior Member
 
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 2,993
Dewey rods are popular with me.
http://www.brownells.com/gun-cleanin...-prod5641.aspx
__________________
The word 'forum" does not mean "not criticizing books."
"Ad hominem fallacy" is not the same as point by point criticism of books. If you bought the book, and believe it all, it may FEEL like an ad hominem attack, but you might strive to accept other points of view may exist.
Are we a nation of competing ideas, or a nation of forced conformity of thought?
Clark is online now  
Old August 5, 2014, 08:50 AM   #7
AllenJ
Senior Member
 
Join Date: December 11, 2009
Location: Northern California
Posts: 1,289
Count me as another vote for Dewy rods. I've been using them for a couple years now and am very pleased with them. I also purchased their bore guides which I really like, well worth the money IMO.
AllenJ is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:11 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07419 seconds with 9 queries