The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old April 1, 2014, 05:18 PM   #1
Sid
Senior Member
 
Join Date: November 22, 2009
Posts: 271
Resizing primed pistol cases

I have a large number of primed .32 ACP cases which need to be resized. Obviously I will remove the decapping pin before doing this. With the pin removed, is there still any danger of a detonation? I would like to get some advice on this, especially from guys who have done this. TIA
Sid is offline  
Old April 1, 2014, 05:22 PM   #2
Misssissippi Dave
Senior Member
 
Join Date: December 5, 2009
Posts: 1,405
I have removed the pin to resize several times after pulling bullets before reloading them again. No problem at all. Just don't try to put another primer in the case while you are at it. 2 primers in one pocket just doesn't get it.
Misssissippi Dave is offline  
Old April 1, 2014, 05:26 PM   #3
g.willikers
Senior Member
 
Join Date: September 28, 2008
Posts: 4,859
Most folks who reload have probably done it.
As long as there's nothing under the primer that can whack it, there's little chance of one going off.
Just make sure the cases are fully into the shell holder and the primers are directly over the empty hole.
If one would go off, without powder or bullet, it would just make noise.
Be sure to wear safety glasses, though.
Ear protection, too, maybe.
__________________
Lock the doors, they're coming in the windows.

Last edited by g.willikers; April 1, 2014 at 05:31 PM.
g.willikers is offline  
Old April 1, 2014, 05:31 PM   #4
Wreck-n-Crew
Senior Member
 
Join Date: March 8, 2013
Location: Ohio
Posts: 1,361
I have de-caped several live primers when they were mixed up (magnum and standard.) Practically all accidental primer ignitions I have encountered have been when seating.
__________________
If you ever have to use a firearm, you don't get to pick the scenario!
Wreck-n-Crew is offline  
Old April 2, 2014, 11:00 PM   #5
Nick_C_S
Senior Member
 
Join Date: March 21, 2013
Location: Taxifornia
Posts: 1,841
Quote:
I have de-caped several live primers when they were mixed up (magnum and standard.)
How does that happen?

If I were in that situation, I would just load that mixed primer brass with middle of the road general purpose rounds. I wouldn't have de-capped them.
__________________
If you ever find yourself in a fair fight, it's because your tactics suck." -- Allen West, quoting Marine 1st Sgt Jim Reinfinger
Nick_C_S is offline  
Old April 3, 2014, 06:47 AM   #6
Alphadawg
Junior Member
 
Join Date: February 16, 2014
Posts: 8
This is mainly advice for new reloaders, maybe a reminder for experienced loaders: When you pull the pin to resize make sure the pin is centered when you re-insert it, otherwise you will break your decapping pin. Don't ask me how I know this
Alphadawg is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:45 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07425 seconds with 9 queries