The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 15, 2001, 10:15 AM   #1
SDC
Senior Member
 
Join Date: January 23, 2001
Location: People's Republic of Kanada
Posts: 1,618
Does anyone out there have any experience with heavy bullet weights in the M1 Garand? I'm thinking up to 173 grain BTHPs, using H-414 powder, but I've heard that some powders have burning rates that can stress the op-rod. Ideally, I'd like to be able to use the same powder and bullets in my bolt-action .308s and my Garands, but is this just a pipe-dream? (PS. I'm using H-414 now for my .308s, and it meters really well, so I'd like to stick with that powder if I can.) Thanks.
SDC is offline  
Old May 15, 2001, 10:43 AM   #2
Pampers
Senior Member
 
Join Date: October 7, 2000
Location: In the Lost State of Franklin
Posts: 482
Slow powders in the M1 Garand

Use no powder slower than IMR 4064 in a Garand! Slower powders will have to much pressure at the gas port, and will overdrive the gas system. This WILL bend the opperating rod! Heavier bullets are also not recommended. The Garand's gas system is not "self regulating" like the M14, and many civilian gas guns. Therefore, loads must be kept within a limited range.

The 173 gr. bullet is fine. It is, after all, the bullet weight used in M72 LC Match ammo for the Garand. I use 46.0 gr. of AA#2520 with the LC 173 gr. bullets in my Garand.


Yr. Obt. Svnt.
__________________
Your Most Humble & Obedient Servant
Fred J. Drumheller
NRA Life
NRA Golden Eagle
Pampers is offline  
Old May 15, 2001, 12:16 PM   #3
Cheapo
Senior Member
 
Join Date: November 19, 1998
Posts: 986
I'm with Fred on this one. The M1 has been successfully used with bullets up to 180 grains and powders as "slow" as 4064, with no problems.

Some folks have used the M1 with 190-grain bullets, but that's the upper limit and beyond what I believe is wise. As stated, it's a port pressure problem.

You may want to try 748 as your powder. It has proven its worth in my .308 loads, it meters VERY well, and it also might extend barrel life by 2-3000 rounds by having a lower flame temperature.
Cheapo is offline  
Old May 15, 2001, 08:27 PM   #4
Southla1
Member In Memoriam
 
Join Date: March 19, 2000
Location: Jeanerette, La. Near the
Posts: 1,999
H414 is too slow. 180 grain bullets on down and 4895 powder are a good combo. A good shooting load is a 147-155 grain bullet over 47 grains of 4895. Hell a lot of the Garands are older than I am..........be kind to em . Mine is younger than I am though..........it was made in March of 1945 .
Southla1 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:29 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06341 seconds with 9 queries