The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 3, 2001, 10:36 AM   #1
salukijoe
Member
 
Join Date: March 22, 2001
Posts: 23
Two questions actually -

Is the mount for Dillon presses only and does it work (and well)?
salukijoe is offline  
Old May 3, 2001, 11:36 AM   #2
ArmySon
Staff Alumnus
 
Join Date: April 14, 2000
Posts: 2,926
If you have a sturdy bench, you don't need the strong mount. It's a nice feature but definitely not needed. Save your money and buy more bullets
ArmySon is offline  
Old May 3, 2001, 11:47 AM   #3
WalterGAII
Junior member
 
Join Date: November 7, 1999
Posts: 1,516
Doesn't the Strong Mount have more to do with the working height of the press, as opposed to the stability of the mount? If you mount a Strong Mount on a Weak Bench, you're still going to have a Wobbly Press.
WalterGAII is offline  
Old May 3, 2001, 11:49 AM   #4
salukijoe
Member
 
Join Date: March 22, 2001
Posts: 23
"Save your money and buy more bullets"

Roger that
salukijoe is offline  
Old May 3, 2001, 12:06 PM   #5
jthuang
Senior Member
 
Join Date: January 21, 2000
Posts: 823
1. Sorry, don't know.

2. It does work, and works well -- for my intended purpose. I have the Strong Mount but I bought it only because my 550B would not fit on my reloading bench due to the short "overhang". Without it, I would have been SOL. But barring that problem and any other problems you may have with mounting, the only other reason I can think to buy the Strong Mount is that you prefer the height differential over the Mount-less press.

Justin
jthuang is offline  
Old May 3, 2001, 04:44 PM   #6
blades67
Senior Member
 
Join Date: April 22, 1999
Location: Chandler, Arizona, USA
Posts: 6,014
If the hole spacing lines up then it will work. (I know, that is an obvious answer, but so it is with obvious questions.)

I use the strong mount to keep my reloading area tight. I don't have much room, so the strong mount keeps the press from hanging off the front of my bench. This does two things for me, it puts the press further out of the way and the leading edge of my bench doesn't have to take all the stress.
__________________
Guns cause crime like spoons cause Rosie O'Donnell to be fat!

I hunt, therefore I am.
blades67 is offline  
Old May 3, 2001, 06:53 PM   #7
HankL
Senior Member
 
Join Date: March 11, 1999
Location: The Sunny South
Posts: 2,174
Hole spacing is 3 1/2" front to back. The strong mount is in two halves so you could vary the width. It will do nothing for an unstable bench except put the center of the ram of a 650 2" back from the front edge of your bench which might help a little. I like the added 6 3/4" height myself.
HankL is offline  
Old May 3, 2001, 10:29 PM   #8
Charmedlyfe
Junior member
 
Join Date: October 11, 2000
Location: SC
Posts: 799
I like the Strong Mount 'cause I can put the cool bullet tray on the left, and have it at the PERFECT height for work. At first, I thought it was just a gimmick (Which, being a Dillonaholic, I would fall for), but after the first session with it, I now consider it a necessity.
Charmedlyfe is offline  
Old May 4, 2001, 01:23 PM   #9
Nukem
Senior Member
 
Join Date: January 29, 2000
Posts: 709

I've got a strong bench, and don't need one. But, the idea behind it is to increase the footprint of the press. The side effect is a higher working height, which comes into play when presses with case feeders are located in basements with low overheads.
Nukem is offline  
Old May 6, 2001, 05:20 PM   #10
slickpuppy
Senior Member
 
Join Date: August 29, 1999
Posts: 928
Get one. I have an extremely strong bench and prefer the height increase the strong mount provides.
slickpuppy is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:34 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07863 seconds with 9 queries