The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old June 4, 2013, 11:19 PM   #1
tkvalead
Junior Member
 
Join Date: January 12, 2013
Location: Westland, Michigan
Posts: 10
Cleaning powder measures

I am just starting to reload and I understand purchasing new equipment comes with a film of rust protection. What is the best way to clean the equipment? I was told to make sure to take the powder measure apart and clean. Any suggestions would be appreciated.
Thank you
thomas
tkvalead is offline  
Old June 4, 2013, 11:32 PM   #2
Lucas McCain
Senior Member
 
Join Date: March 7, 2013
Location: Callaway, MN
Posts: 187
I clean my powder measure with alcohol, from the drug store. I lube my measures with a very light coat of silicone lubricant to prevent any corrosion.
__________________
If you have time to do it twice, then you have time to do it once right and put your name on it
Lucas McCain is offline  
Old June 4, 2013, 11:59 PM   #3
Fire_Moose
Senior Member
 
Join Date: January 16, 2013
Posts: 206
Re: Cleaning powder measures

Agreed. Stay away from the expensive whiskey tho. Popov works just as good.
Fire_Moose is offline  
Old June 5, 2013, 08:16 AM   #4
Rifleman1776
Senior Member
 
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
Spray carburetor cleaner is my go-to degunker for almost everything. Just keep it off of painted surfaces.
Rifleman1776 is offline  
Old June 5, 2013, 09:04 AM   #5
daboone
Member
 
Join Date: August 23, 2011
Location: Peoria AZ
Posts: 25
I just use dish soap and water with a final alcohol rinse to help evaporate the water. After it's dry I'd use graphite powder (found in hardware stores) or run 1 to 3 hoppers full of any powder to lube the measure. Stay away from any kind of lube that's leave a sticky/oily film for obvious reasons.
daboone is offline  
Old June 5, 2013, 10:02 AM   #6
Swampman1
Senior Member
 
Join Date: February 17, 2013
Location: South Louisiana
Posts: 406
Or you can use Hornady One Shot which works very well.
Swampman1 is offline  
Old June 5, 2013, 10:49 AM   #7
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,187
Quote:
Originally Posted by Rifleman1776
Spray carburetor cleaner is my go-to degunker for almost everything. Just keep it off of painted surfaces.
Keeping it off plastic powder hoppers is probably more important. It can destroy them. Alcohol is generally safe for plastic.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Patron Member
Unclenick is offline  
Old June 5, 2013, 11:18 AM   #8
David Bachelder
Senior Member
 
Join Date: August 23, 2011
Location: Trinity, Texas
Posts: 618
Something I learned. After cleaning and re-assembling everything. Wipe the plastic hopper down with a drier sheet. Next put a small amount of powdered graphite on a small brush and swish it inside the measure. Be sure to dump the measure several times, tap the sides and dump, repeat several times. The graphite is a dry lube and will help keep things moving smoothly. I does stain the plastic hopper a bit, but it's a good trade. Everything will operate very smooth. I clean mine with Hornady One Shot Gun Cleaner and Dry Lube.

Smokeless and Black powder contain a small amount of graphite, so you will stain the plastic either way.

You can find powdered graphite at most hardware stores, it's used to lubricate locks. I've seen it in small plastic squeeze tubes.
__________________
David Bachelder
Trinity, Texas
I load, 9mm Luger, 38 and 40 S&W, 38 Special, 357, 45ACP, 45 Colt, 223, 243 and 30-06
David Bachelder is offline  
Old June 5, 2013, 02:40 PM   #9
schmellba99
Senior Member
 
Join Date: January 8, 2008
Posts: 570
Hornady One Shot works well for me.

Stay away from any oil based lubricants. I had a brain fart one time and failed to adhere to that rule (why I reload with no distractions anymore). I didn't lose much powder, but I lost a couple of hours disassembling my powder measure and re-cleaning and lubricating everything after I discovered my ruh-roh.

Powdered graphite (or moly works well too) and rubbing it down with a dryer sheet or swiffer on occasion to eliminate static electricity. I have a long brush I use to reach down inside it to push all the powder out of the rotor when I'm changing powders as well.

All in all, it's a simple process and it is fairly maintenance free compared to most other things.
schmellba99 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:20 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08259 seconds with 9 queries