The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 31, 2013, 06:07 PM   #1
JefferS
Member
 
Join Date: April 27, 2013
Location: Independence, MO
Posts: 57
Do you use lead data for Rainier Bullets?

I'm still a novice, but I've had some overall success. I've looked at other threads and didn't find this question directly answered, so I hope I didn't miss it and repeated an answered question.

I was told by someone with just a little more experience than I have that for Rainier plated bullets (as opposed to jacketed), you use similar lead bullet load starting and max points.

My specific case is that I am loading 38 Special with Bullseye. 3.4 to 4.2 grain with Hornady XTP 158 gr JHP (#35750) with 1.445 OAL seemed reasonably accurate. I changed my crimp a bit and need to go back to the range and check those.

Now, I have obtained some Rainer 158 gr Round Nose. Not a lot to choose from these days, so I got what I could. So would I use data from, say, the Lyman 49th edition for lead, which has a starting point with Bullseye at 3.0 and max fo 3.4?
__________________
Jeff
JefferS is offline  
Old May 31, 2013, 06:33 PM   #2
Ashbane
Member
 
Join Date: May 29, 2013
Posts: 48
I am also just starting so until someone who knows better comes along I can just say I bought some Berry's bullets and was told something similar, that they are copper plated and to use the lead bullet section of the manual. I did, however find load data from Hogdgon's website that specifically referred to the powder I was using to the bullet I had. I also found Hornady's book limited in info and in the Lee book Modern Reloading found they actually list copper plated bullets in addition to the lead and jacketed, etc...

Hope this helps...
Ashbane is offline  
Old May 31, 2013, 07:25 PM   #3
rg1
Senior Member
 
Join Date: November 6, 2001
Posts: 752
Check this info and compare it to other 115 grain data, both lead and jacketed: http://cakesniffer.org/stuff/boom/RanierData.pdf
Doesn't have .38 Special data but it might answer your question about using lead bullet data to compare to Rainier bullets.
This is what Rainier says about their bullets: http://www.rainierballistics.com/loaddata.php

Last edited by rg1; May 31, 2013 at 07:31 PM.
rg1 is offline  
Old May 31, 2013, 07:58 PM   #4
arizona98tj
Senior Member
 
Join Date: December 10, 2007
Location: Arizona
Posts: 946
Straight from BerrysMfg web site:

Plated bullets occupy a position between cast bullets and jacketed bullets. They are soft lead, but have a hard outer shell on them. When loading plated bullets we have found best results using low- to mid-range jacketed data in the load manual. You must use data for a bullet that has the same weight and profile as the one you are loading. Do not exceed mid-range loads. Do not use magnum loads.

I follow their advice and have had no issues having shot thousands of their bullets. Out of my 4" XD9, I get 1130 FPS with their 115 gr bullet.

Were I shooting Ranier bullets, it's not likely I would change my load (after working up to it) unless I had problems with plating separation, etc.
__________________
stu-offroad.com
Largest Jeep TJ project site on the web!
(now with guns)
arizona98tj is offline  
Old May 31, 2013, 08:14 PM   #5
mikld
Senior Member
 
Join Date: February 7, 2009
Location: Southern Oregon!
Posts: 1,054
http://www.rainierballistics.com/loaddata.php

Not too hard to find...
__________________
My Anchor is holding fast!
mikld is offline  
Old May 31, 2013, 10:38 PM   #6
BuckRub
Junior member
 
Join Date: October 3, 2012
Location: Central Texas
Posts: 1,046
I've shoot tons of them and do as post #4 stated.
BuckRub is offline  
Old June 4, 2013, 09:57 AM   #7
pbcaster45
Member
 
Join Date: October 23, 2010
Posts: 80
I haven't loaded the round nose version but here's one using the 158 gr. FN. Shoots great in my Colt Python and S&W Model 10.

Bullet: Rainier 158 gr. FN
Powder: Hodgdon HP38 4.3 grs.
Primer: CCI-500
Case: Federal .38 Special
LOAL: 1.450 (Taper Crimp)
pbcaster45 is offline  
Old June 5, 2013, 06:41 AM   #8
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,204
I do NOT use Rainier data

I have loaded Rainiers, both for personal and commercial consumption, in 9x19, 9x21, 38 Super, 38 Special, 357 Magnum, 40 S&W, 400 CorBon, 10mm, 44 Magnum, 45 ACP, and 45 Colt.

I still use Rainiers in a few personal loads.

I use averaged (from my many data sources) start charges from jacketed data.





(Mostly now I use lead or jacketed bullets. They're normally better.)
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:29 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07190 seconds with 9 queries