The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old April 20, 2013, 05:53 AM   #26
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 11,758
Captchee, you sir are a master craftsman.
Hawg is offline  
Old April 20, 2013, 11:08 AM   #27
Doc Hoy
Senior Member
 
Join Date: October 24, 2008
Location: Chesapeake, VA
Posts: 4,598
Thats a fact!

Hawg is right
__________________
Doc

My reading of history convinces me that most bad government results from too much government. Thomas Jefferson
Doc Hoy is offline  
Old April 20, 2013, 07:08 PM   #28
PPQ226guy
Member
 
Join Date: February 4, 2012
Location: Alabama
Posts: 93
Indeed. That is a beautiful weapon. Bravo, Sir.
PPQ226guy is offline  
Old April 24, 2013, 02:11 PM   #29
chickenmcnasty
Senior Member
 
Join Date: December 10, 2012
Location: Wichita, KS
Posts: 148
Re: Browning a brown Bess barrel

Well the process went really smooth. There was an area on the underside and a little on the sides of the barrel where the browning would not take. It shows a little when the barrel is back on the gun, but not enough to be concerned.
The picture doesn't do it justice as it picks up a lot of light, but it really looks great. Thank you all for the advice.
Attached Images
File Type: jpg uploadfromtaptalk1366830454777.jpg (86.7 KB, 29 views)
chickenmcnasty is offline  
Old January 8, 2014, 07:07 PM   #30
sixteenacrewood
Member
 
Join Date: January 20, 2013
Posts: 35
sorry for bumping up an old thread, but I just found this on a google search of rust browning with bleach.

Thanks Captchee for posting the photos. The info on the process and helpful tips are a great value to the rest of us!!

I normally haunt the C & R and shotgun sections, but I would like to ask a few questions here and see if any of you may have some insight.

I have recently decided to do a project shotgun and had intended to do a cold blueing of the entire barrel and reciever, it is a pump, no colector value, savage springfield from 1952.

After some research I have almost decided to do this bleach rust browning method. I love the color and patina and really want to try the process.

Do you think this would be appropriat for the kind of steel this shotgun is made of?

Thanks again
sixteenacrewood is offline  
Old January 8, 2014, 07:41 PM   #31
Captchee
Senior Member
 
Join Date: April 2, 2013
Posts: 322
the bleach method may not take to well as the modern steel has less iron in it . but frankly i have not tried it on modern steels. Frankly I have not tried iton such a barrel . Now I have done it on old Remington’s , Winchesters and such as rust Black was a process that was often used . Especially on Parkers.
In the long run it will produce a far more resilient finish then cold blue .
If it were me , I would use a slow rust method using laurel mountain. By using that with repeated boils and carding , you will get a very nice smooth black color

Chicken ,
you need to oil the barrel with a good oil . i use motor oil . do you best to keep it good and wet for 12 -24 hours . then whipe it down . doing so will help stop the rusting so that the finish stays fine and smooth
Captchee is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:59 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07097 seconds with 10 queries